EasyManuals Logo

NEC MultiSync V552 User Manual

NEC MultiSync V552
47 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #21 background imageLoading...
Page #21 background image
English-19
English
Information OSD
The Information OSD provides information such as: Monitor ID, Input Source, Picture Size, etc.
Press the DISPLAY button on the remote to bring up the Information OSD.
ID number assigned to current monitor*
1
ID number assigned monitor to be controlled via RS-232C*
2
Input Name
Audio input mode
Picture aspect
Input Signal Information
Sub picture information
*1: “IR CONTROL” should be set “Primary” or “Secondary”.
*2: “IR CONTROL” should be set “Primary”.
Picture Mode
DVI, VGA, RGB/HV, DPORT
STANDARD sRGB AMBIENT1 AMBIENT2 HIGHBRIGHT
HDMI, DVD/HD, SCART, VIDEO1, VIDEO2, S-VIDEO
STANDARD CINEMA AMBIENT1 AMBIENT2 HIGHBRIGHT
AMBIENT Mode
The backlight of the LCD screen can be set to increase or decrease depending on the amount of ambient light within the room.
If the room is bright, the monitor becomes correspondingly bright. If the room is dim, then the monitor will dim accordingly. The
purpose of this function is to make the viewing experience more comfortable to the eye in a variety of lighting conditions.
NOTE: When picture mode is set to AMBIENT1 or AMBIENT2, BACKLIGHT, AUTO BRIGHTNESS and BACKLIGHT in
SCREEN SAVER function are disabled.
Do not cover Ambient light sensor when you use AMBIENT1 or AMBIENT2 in PICTURE MODE.
AMBIENT parameter setting
PICTURE MODE in OSD, select AMBIENT1 or AMBIENT2 and set IN BRIGHT and IN DARK in each mode.
IN BRIGHT: This is the backlight level that the monitor will go up to when the ambient light level is highest.
IN DARK: This is the level of backlight that the monitor will go down to when the ambient light level is low.
When the AMBIENT function is enabled the Backlight level of the screen changes automatically according to the lighting
conditions of the room (Figure 1).
BACKLIGHT level set
for the monitor to use
when ambient lighting
level is low.
BACKLIGHT level set for the
monitor to use when ambient
lighting level is high.
BACKLIGHT range
Figure 1
dark bright
room bright condition
Screen Backlight value by AMBIENT2 mode
IN DARK IN BRIGHT
Screen Backlight value by AMBIENT1 mode
Factory Setting
IN DARK: BACKLIGHT level set for the monitor to use when ambient lighting level is low.
IN BRIGHT: BACKLIGHT level set for the monitor to use when ambient lighting level is high.

Other manuals for NEC MultiSync V552

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the NEC MultiSync V552 and is the answer not in the manual?

NEC MultiSync V552 Specifications

General IconGeneral
Panel life- h
Pixel pitch0.63 x 0.63 mm
Response time8 ms
Display diagonal55 \
Display brightness430 cd/m²
Display technologyLCD
Native aspect ratio16:9
Vertical scan range50 - 85 Hz
Horizontal scan range31.5 - 91.1 kHz
LED backlighting typeEdge-Lit LED
Supported video modes1080p
Touchscreen technologyInfrared
Display number of colors16.78 million colors
Active display area (W x H)1209.6 x 680.4 mm
OrientationHorizontal/Vertical
Product colorBlack
Product designDigital signage flat panel
Bezel width (top)41.4 mm
Panel mounting interface300 x 300 mm
Wi-Fi-
DVI-D ports quantity2
Cable lock slot typeKensington
Power consumption (standby)2 W
Power consumption (typical)100 W
Package depth250 mm
Package width1430 mm
Package height920 mm
Operating altitude0 - 3000 m
Non-operating altitude3000 - 12192 m
Storage temperature (T-T)-20 - 60 °C
Operating temperature (T-T)5 - 40 °C
Storage relative humidity (H-H)10 - 90 %
Operating relative humidity (H-H)20 - 80 %
RMS rated power10 W
Cables includedAC, DVI
Weight and Dimensions IconWeight and Dimensions
Depth86.5 mm
Width1294.4 mm
Height765.2 mm
Weight40800 g

Related product manuals