NEC NC1200C User Manual

2
Precautions:
Please read this manual carefully before using your
NC2000C and keep the manual handy for future reference.
Important Safeguards
These safety instructions are to ensure the long life of your
projector and to prevent fire and shock. Please read them
carefully and heed all warnings.
WARNING
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT
EXPOSE THIS UNIT TO RAIN OR MOISTURE.
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT OPEN COVER. NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This symbol warns the user that uninsulated
voltage within the unit may have sufficient
magnitude to cause electric shock. Therefore,
it is dangerous to make any kind of contact
with any part inside of this unit.
This symbol alerts the user that important
literature concerning the operation and
maintenance of this unit has been included.
Therefore, it should be read carefully in
order to avoid any problems.
CAUTION
• In order to reduce any interference with radio and television
reception use a signal cable with ferrite core attached. Use of
signal cables without a ferrite core attached may cause
interference with radio and television reception.
• This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the
user will be required to correct the interference at his or her
own expense.
WARNING
This is a Class A product. In a domestic environment this
product may cause radio interference in which case the user
may be required to take adequate measures.
DOC compliance Notice
This Class A digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.
Important Information
Machine Noise Information Regulation - 3. GPSGV,
The highest sound pressure level is less than 70 dB (A) in
accordance with EN ISO 7779.
Disposing of your used product
EU-wide legislation as implemented in each Member
State requires that used electrical and electronic
products carrying the mark (left) must be disposed
of separately from normal household waste.
This includes projectors and their electrical
accessories or lamps. When you dispose of
such products, please follow the guidance of
your local authority and/or ask the shop where
you purchased the product.
After collecting the used products, they are
reused and recycled in a proper way. This
effort will help us reduce the wastes as well
as the negative impact to the human health
and the environment at the minimum level.
The mark on the electrical and electronic products
only applies to the current European Union Member
States.
WARNING
Installation and transport
Consult your dealer for installing and transporting the projector.
DO NOT install or transport the projector by non-professional
person. Doing so may cause the lamp to break or may cause
personal injury.
• Power Supply
- Consult your dealer for installing the power cable to the
projector. DO NOT install the power cable by yourself.
Doing so may cause a fire or electric shock.
- The projector is so designed that it operates with the
power supply voltage described below.
For C1 connection
(When the AC power to the projector power supply and
the lamp power supply is provided by a single cable)
•AC 200V-240V single phase 50/60Hz
For C2 connection
(When the AC power to the projector power supply and
the lamp power supply is provided by separate cables)
•AC 100V-240V single phase 50/60Hz (projector
power supply)
•AC 200V-240V single phase 50/60Hz (lamp power
supply)
Ensure that your power supply fits this requirement
before attempting to use your projector.
- Handle the power cable carefully. A damaged or frayed
power cable can cause electric shock or fire.
• Do not bend or tug the power cable excessively.
• Do not place the power cable under the projector, or
any heavy object.
• Do not cover the power cable with other soft materials
such as rugs.
• Do not heat the power cable.
•Turn off the projector, shut down AC power by using a circuit
breaker and contact qualified service personnel under the
following conditions. For C2 connection, turn off the projec-
tor, shut down the AC power to the projector and the lamp
using a circuit breaker, and contact your dealer/distributor
for a repair.

NEC NC1200C Specifications

General

Brand	NEC
Model	NC1200C
Category	Projector
Language	English