Neomitis RT7 RF - Operating Modes and Temperature Settings; Mode Selection; Manual Override; Boost Function

5- Movetheprogrammodeslidertothe positiontoconrmand
nishallprevioussettings.
4- Turnthedialtosetthetempe
-
raturebetween5°Cand30°C,
in increments of 0.5°C.
 MovetheProgramslidertothe
nextpositiontoconrm/nish
this setting.
NOTE: This is the temperature
thattheunitwillworktooutside
of your comfort periods.
4- Turnthedialtosetthetime.
MovetheProgramslidertothe
nextpositiontoconrm/nish
this setting.
3- TosettherstComfortend
time, move the Programming
slidertoposition .
 Thedefaulttimeis8:30am.
MANUAL: A TEMPORARY CHANGE
MANUAL: Indicates when the
temperature has been moved
fromsetpoint.Thistemperaturewill
operateuntilthenextswitching
time.Thisisonlyactivewhenthe
controllerisinAUTOorCOMFORT
mode.
Note:theProgrammingslidermustbeinthe position.
BOOSTiscancelledbyanypressofbutton,movementofdialorslider.
WhenBOOSTisrunningthetimeanddaydisappear.Theminutearraywill
countdownfrom60–0toindicatetimeleftinBOOSTmode.
BOOST
BOOST: Boost mode is a temporary
modewhichallowsyoutoope-
rate at the comfort temperature
for 1 hour. At the end of 1 hour the
devicewillreverttoitspriorsetting.
BOOSTwillworkfromanyrunningmode.
BOOST is entered by pressing / button.
am
Tu
C
C
3
OPERATING
MODE SELECTION AND DESCRIPTION
Mode sliders sequences:
Auto mode Comfort mode Economy mode Standby.
STANDBY: Permanent standby
mode with frost protection. The
unitiscontrollingcontinuously
at the frost protection tempera
-
ture factory set. i.e 8°C.
ECO: Permanent eco mode.
Theunitiscontrollingconti-
nuouslytotheecotemperature
setpoint.Thedefaulttempe-
rature setting is 10°C (50°F).
Refer to section temperatures
settingtochangethevalue
page 2.
AUTO: Automatic mode. The
unitiscontrollingtothetime
and temperature program
thathavebeenselected(re-
fer to "programming" section
page 2).
COMFORT: Permanent comfort
mode.Theunitiscontrolling
continuouslytothecomfort
temperature setpoint. The
defaulttemperaturesettingis
20°C(68°F).Refertosection
temperatures setting to
changethevalue page 2.
5- Repeat for the second comfort period , and for the third comfort
period .
TEMPERATURES SETTING
Two temperatures can be set: Comfort temperature and Economy
temperature.
2- Turnthedialtosetthetempe
-
raturebetween5°Cand30°C,
in increments of 0.5°C.
 MovetheProgramslidertothe
nextpositiontoconrm/nish
this setting.
1- To set the Comfort tempera-
ture, move the Programming
slidertoposition .
 Thedefaulttemperatureis20°C
(68°F).
3- To set the Economy tempera-
ture, move the Programming
slidertoposition .
 Thedefaulttemperatureis10°C
(50°F).
Comfort period Default times
Comfort period 2 Start at 12:00
pm
End at 02:00
pm
Comfort period 3 Start at 05:00
pm
End at 10:00
pm
Note: if you wish not to use a period then this can be done by Coinciding
the End time with Start time.