NETGEAR DM111P User Manual (English)

Other manuals for NETGEAR DM111P

Questions and Answers:

C
Cindy CarterAug 13, 2025
What to do if my computer is connected to my NETGEAR Wireless Router via a router, and I don't have internet access?
- P
  Pamela ReevesAug 13, 2025
  If your computer is connected to your NETGEAR Wireless Router via a router, disconnect the router and directly connect the computer to the modem. If your modem is unable to access the internet, but your Internet LED is green or blinking green, you should determine whether the modem is able to obtain an IP address from the ISP.
B
Brian BassAug 17, 2025
What to do if my computer does not recognize any DNS server addresses when using NETGEAR Wireless Router?
- J
  Jeffrey SullivanAug 17, 2025
  If your computer does not recognize any DNS server addresses while using a NETGEAR Wireless Router: 1. If you entered a DNS address during the modem’s configuration, reboot your computer and verify the DNS address. 2. Alternatively, you can configure your computer manually with DNS addresses.
C
claudia31Aug 21, 2025
What to do if the ADSL light is blinking on my NETGEAR Wireless Router?
- J
  jasonwadeAug 21, 2025
  If the ADSL light on your NETGEAR Wireless Router, which was previously solid, is now blinking, try the following: 1. Switch off the modem, wait 30 seconds, and then switch it back on again. 2. Check with your ISP to ensure that there are no service interruptions. 3. If you recently installed a telephone or other device that uses telephone lines, ensure it's connected via a microfilter. 4. Log in to the modem and run the ADSL Bit Error Test (BER) and modem diagnostics, and contact your ISP’s technical support representative.
A
Anthony WarnerAug 25, 2025
How to fix NETGEAR Wireless Router if the Power and other LEDs are off?
- W
  William DanielsAug 25, 2025
  If the power and other LEDs on your NETGEAR Wireless Router are off when you turn it on, ensure the following: 1. The power cord is properly connected to your modem. 2. The power supply adapter is properly connected to a functioning power outlet. 3. The power switch on the back of the modem is pressed in. 4. You are using the 12 V DC power adapter supplied by NETGEAR for this product. If the issue persists, it may indicate a hardware problem, and you should contact technical support.
C
Cynthia NewmanAug 28, 2025
What to do if my NETGEAR Wireless Router was just installed and the LED has never been solid on?
- R
  russellchristinaAug 28, 2025
  If you've just installed your NETGEAR Wireless Router and the LED has never been solid, try these steps: 1. Disconnect all telephones on the line. 2. If this solves the problem, reconnect the telephones one at a time, being careful to use a micro-filter on each telephone. 3. If disconnecting telephones does not result in a green Internet LED, there may be a problem with your wiring. 4. Verify that you are connected to the correct telephone line.
C
Christopher SimpsonAug 31, 2025
Why won't my NETGEAR Wireless Router save changes made in the Web Management Interface?
- A
  Antonio CannonSep 1, 2025
  If your NETGEAR Wireless Router doesn't save changes made in the Web Management Interface: 1. When entering configuration settings, be sure to click the Apply button before moving to another screen, or your changes will be lost. 2. Click the Refresh or Reload button in the Web browser. The changes may have occurred, but the Web browser may be caching the old configuration.
J
John MullinsSep 4, 2025
What to do if the NETGEAR Wireless Router Power LED never turns green?
- C
  Crystal DaughertySep 4, 2025
  If the Power LED on your NETGEAR Wireless Router never turns green: 1. Cycle the power to see if the modem recovers, as the modem’s self-test might have failed. 2. Clear the modem’s configuration to factory defaults. This will set the modem’s IP address to 192.168.0.1. If the error persists, you might have a hardware problem and should contact technical support.

NETGEAR DM111P Specifications

Power

power requirements	12V DC, 1.0A
power adapter localization	Plug is localized to country of sale, RoHS compliant

Operating Environment

operating temperature	0° to 40°C (32 to 104ºF)
non-operating temperature	-20° C to 70° C
operating humidity	10-90% relative humidity, noncondensing
non-operating humidity	5-95% relative humidity, noncondensing

System Memory