New Holland B95CTC - User Manual

Questions and Answers

L
Lauren AllisonNov 19, 2025
How to troubleshoot New Holland B95CTC Front End Loaders when the engine does not start?
- R
  Ryan KaneNov 19, 2025
  If the New Holland Front End Loaders engine does not start, several issues could be the cause. It could be due to partially discharged batteries, so check and charge them, replacing if necessary. Corroded or loose connections to the battery terminals can also prevent starting; clean, inspect, and tighten the nuts, replacing corroded parts as needed. Other potential causes include dirt or water in the fuel lines, requiring you to disconnect and clean the lines and possibly the fuel tank. Ensure there is fuel in the tank and that the supply pump is functioning correctly; replace it if necessary. Finally, air in the fuel system can also prevent starting; check for air in the lines, fittings, supply pump, filters, and injection pump, then bleed the system. A damaged starter motor could also be...
C
Chase DyerNov 25, 2025
Why does my New Holland Front End Loaders vehicle not move?
- D
  Dillon CookNov 25, 2025
  If the New Holland Front End Loaders vehicle does not move, several issues could be the cause. A control valve supply problem can prevent movement, so check and replace the control valves if necessary. Damaged connections of the transmission and vehicle wiring harness can also be the issue; repair or replace the wiring harness. Oxidation in the contacts of the electric cables or an interruption of the electric cable can also cause this; clean the contacts or replace the electric cable. Damage to the solenoids/solenoid valves or sensors can also prevent movement, so replace these components. Short circuits or bad contact can also be the issue; check and replace the fuses if needed. For POWERSHIFT models, an EGM/ECU gearshift electronic control operation fault can be the cause, so replace th...
J
John GutierrezNov 27, 2025
What causes anomalous knocking in my New Holland B95CTC Front End Loaders engine?
- T
  Timothy BennettNov 27, 2025
  If the New Holland Front End Loaders engine has anomalous knocks, several issues could be the cause. Partially obstructed or damaged injectors can cause knocking, so clean, overhaul, and correctly calibrate the injectors. Dirt accumulations in fuel lines can also cause this; clean the lines and replace any visibly dented pipes, and clean the injection pump if necessary. Drive shaft knocks caused by excessive clearance of crankshaft or big end bearings or excessive shoulder clearance can also be the issue; rectify the drive shaft pins and assemble bigger shoulder bearings and rings. An unbalanced drive shaft can also cause knocking; check the alignment and balance of the drive shaft and replace it if necessary. Loose flywheel retaining screws can also be the cause; replace the loose screws ...
Z
zmendozaDec 1, 2025
Why does my New Holland B95CTC Front End Loaders vehicle have reduced power transmission?
- P
  Paul HaynesDec 1, 2025
  If the New Holland Front End Loaders vehicle has a reduced power transmission, it could be due to several reasons. An incorrect oil temperature can reduce power, so wait for the operating temperature to be reached (stall test). Transmission oil overheating can also cause this; restore acceptable temperature values. Incorrect operating pressures can also reduce power; check the hydraulic circuit and replace components such as the oil pump, filters, or control valve. A damaged converter can also cause reduced power, so replace the converter. Other potential causes include an incorrect oil level, a worn-out clutch assembly, failure of the 4WD to engage, or overheated solenoids/solenoid valves; restore the oil level, replace/repair the clutch assembly, repair/replace the 4WD shaft assembly, or...
E
Elizabeth KellerDec 1, 2025
What causes overheating in my New Holland B95CTC?
- E
  Ernest HernandezDec 1, 2025
  If the New Holland Front End Loaders is overheating, several issues could be the cause. A damaged cooling system can cause overheating, so repair the cooling system. A dirty heat exchanger can also be the issue; clean the heat exchanger. An unintentionally activated parking brake can also cause overheating; deactivate the parking brake. Excessive soil deposit on axle wheel hubs can also cause this; clean the axle wheel hubs. Seizure (broken gears, shafts, bearings, etc.) can also cause overheating; check, repair, and replace any damaged components. Braking force external to the transmission or an axle operating problem can also cause this; check and repair the axle. Dragging of clutch disks, a damaged converter, a damaged oil thermostat, an incorrect oil level, or a worn-out oil pump can a...

New Holland B95CTC Specifications

General

Brand	New Holland
Model	B95CTC
Category	Front End Loaders
Language	English

Summary

General Information

Foreword

Introduction to the operator's manual and machine capabilities.

Intended Use and Safety Guidelines

Details on the machine's proper use and essential safety precautions.

Component Identification and Manuals

Information on technical manuals and component identification plates.

Safety Information

Signal Word Definitions and Personal Safety

Explains safety alert symbols, DANGER, WARNING, CAUTION, and NOTICE messages.

General Safety Rules and Precautions

Covers essential safety practices for machine operation and maintenance.

Safety Rules for Specific Systems

Details safety precautions for air conditioning, battery, and fuel handling.

Safety Rules for Operational Hazards

Guidelines for lifting, overhead loads, and hazardous chemicals.

Safety Rules for Mechanical Operations

Precautions for mounting, dismounting, and general operator safety.

Safety Rules for Protective Structures and Seat Belts

Ensuring safety with ROPS/FOPS and proper seat belt usage.

Hand Signals and Warning Decals

Visual communication and safety sign information for machine operation.

Controls and Instruments

Operators Platform Access and Controls

Instructions for accessing the operator's compartment and using controls.

Operators Seat Adjustments

Detailed guide on adjusting the operator's seat for comfort and safety.

Forward Controls and Starter Switch

Overview of front controls including starter switch and horn.

Steering Column and Pedal Controls

Information on steering column adjustment and pedal operations.

Transmission Controls and Operation

Details on Power-Shuttle and Power-Shift transmission controls.

Instrument Cluster Overview

Description of the front and side instrument clusters and their functions.

Maintenance Settings and DPF Regeneration

Procedures for accessing maintenance menus and DPF regeneration.

Loader Attachment Controls and Operation

Instructions for operating loader attachments and specific controls.

Backhoe Attachment Controls

Detailed guide on operating backhoe attachment controls and configurations.

Climate Controls and Cab Air Louvers

Operation of heating, ventilation, and air conditioning systems.

Operating Instructions

Unit Commissioning and Pre-Operation Checks

Steps to take before operating the machine, including checks and familiarization.

Machine Operation and Job Site Considerations

Guidelines for safe operation on job sites and road travel.

Engine Starting Procedures

Detailed steps for starting the engine in various conditions.

Stopping the Engine and Moving the Unit

Procedures for safely stopping the engine and moving the machine.

Drive System Operations

Information on 2WD/4WD engagement and differential lock usage.

Parking the Unit

Correct procedures for parking the machine safely.

Transport Operations

Road Transport Requirements and Precautions

Essential requirements and safety measures for road travel.

Preparing Machine for Road Travel

Steps to prepare the machine for safe road transportation.

Locking Backhoe Attachment for Transport

Procedures for mechanically or electrically locking the backhoe attachment.

Shipping and Recovery Transport

Guidelines for transporting the machine on trailers and recovery towing.

Working Operations

General Operating Conditions

Operating guidelines for cold weather, high altitude, and hot temperatures.

Machine Lifting and Attachment Handling

Procedures for lifting the machine and handling loader/backhoe attachments.

Loader Attachment Operation and Safety

Instructions for organizing job sites and operating the loader attachment.

Backhoe Attachment Operation and Safety

Guidelines for operating the backhoe attachment and safety procedures.

Telescopic Dipper and Trenching Techniques

Operating procedures for telescopic dippers and trenching.

Ballasting and Weighting Limitations

Information on tire ballasting and machine weight limitations for stability.

Maintenance

Fluids, Lubricants, and Fuel Information

Summary table of fluids, lubricants, and details on biodiesel fuel usage.

General Safety and Machine Care

Essential safety instructions and general machine care guidelines.

Maintenance Intervals and Schedule

Overview of service intervals, work hours, and the maintenance chart.

10-Hour Maintenance Checks

Procedures for daily checks including general inspection and brake operation.

50-Hour Maintenance Tasks

Routine maintenance including fuel pre-filter, tire pressure, and AC system checks.

250-Hour Maintenance Tasks

Checks and maintenance for ROPS/FOPS, seat belts, air filters, and radiators.

500-Hour Maintenance Tasks

Procedures for engine oil and filter replacement, and fuel system maintenance.

1000-Hour Maintenance Tasks

Inspection, cleaning, and replacement of engine air filters and transmission components.

Axle and Brake System Maintenance

Procedures for changing axle and brake pedal lever lubrication.

Hydraulic System Maintenance

Replacing hydraulic filters, changing hydraulic oil, and checking cylinders.

Battery and Charging System Maintenance

Checking battery electrolyte level and alternator status.

Cooling System and Fuel System Maintenance

Procedures for engine coolant service and fuel system bleeding.

Drive Belt and Air Filter Element Maintenance

Replacing drive belts and cleaning/replacing air filter elements.

Fuse and Relay Checks

Identification and replacement of fuses and relays in the cab and ROPS.

Battery Removal and Installation

Safe procedures for removing and installing the machine battery.

Bucket Teeth Replacement

Instructions for replacing bucket teeth on loader and backhoe attachments.

Loader Bucket Self-Levelling Adjustment

Adjusting the loader bucket's automatic self-levelling control system.

Storage Procedures

Guidelines for storing the machine and engine to prevent damage.

Troubleshooting

Fault Code Resolution Overview

Guide to understanding and resolving fault codes.

Engine Troubleshooting

Common engine problems, their causes, and solutions.

Starter Motor and Alternator Issues

Diagnosing and correcting problems with the starter motor and alternator.

Transmission and Axle System Problems

Troubleshooting transmission and axle related issues.

Steering and Hydraulic System Issues

Diagnosing problems with the steering and hydraulic systems.

Attachment Troubleshooting

Resolving issues with loader and backhoe attachments.

Specifications

Engine and Powertrain Specifications

Detailed specifications for the engine and powertrain components.

Brakes, Controls, and Hydraulics

Technical specifications for braking, steering, and hydraulic systems.

Bucket and Tire Specifications

Details on bucket types, capacities, and tire specifications.

Dimensions and Performance Data

Machine dimensions and performance metrics for loader and backhoe attachments.

Accessories

Loader Attachment Quick Couplers

Installation and removal of mechanical quick couplers for loader buckets.

Backhoe Attachment Auxiliary Tools

Using and selecting flow for backhoe auxiliary hydraulic tools.

Backhoe Attachment Safety Valves

Function and checks for backhoe attachment safety valves.

Reversible Stabilizer Pads

Information on the use and positioning of reversible stabilizer pads.

Related product manuals

New Holland LB115.B 4WS

41 pages

New Holland B95CTC - User Manual

Table of Contents

Questions and Answers

New Holland B95CTC Specifications

Summary

General Information

Foreword

Intended Use and Safety Guidelines

Component Identification and Manuals

Safety Information

Signal Word Definitions and Personal Safety

General Safety Rules and Precautions

Safety Rules for Specific Systems

Safety Rules for Operational Hazards

Safety Rules for Mechanical Operations

Safety Rules for Protective Structures and Seat Belts

Hand Signals and Warning Decals

Controls and Instruments

Operators Platform Access and Controls

Operators Seat Adjustments

Forward Controls and Starter Switch

Steering Column and Pedal Controls

Transmission Controls and Operation

Instrument Cluster Overview

Maintenance Settings and DPF Regeneration

Loader Attachment Controls and Operation

Backhoe Attachment Controls

Climate Controls and Cab Air Louvers

Operating Instructions

Unit Commissioning and Pre-Operation Checks

Machine Operation and Job Site Considerations

Engine Starting Procedures

Stopping the Engine and Moving the Unit

Drive System Operations

Parking the Unit

Transport Operations

Road Transport Requirements and Precautions

Preparing Machine for Road Travel

Locking Backhoe Attachment for Transport

Shipping and Recovery Transport

Working Operations

General Operating Conditions

Machine Lifting and Attachment Handling

Loader Attachment Operation and Safety

Backhoe Attachment Operation and Safety

Telescopic Dipper and Trenching Techniques

Ballasting and Weighting Limitations

Maintenance

Fluids, Lubricants, and Fuel Information

General Safety and Machine Care

Maintenance Intervals and Schedule

10-Hour Maintenance Checks

50-Hour Maintenance Tasks

250-Hour Maintenance Tasks

500-Hour Maintenance Tasks

1000-Hour Maintenance Tasks

Axle and Brake System Maintenance

Hydraulic System Maintenance

Battery and Charging System Maintenance

Cooling System and Fuel System Maintenance

Drive Belt and Air Filter Element Maintenance

Fuse and Relay Checks

Battery Removal and Installation

Bucket Teeth Replacement

Loader Bucket Self-Levelling Adjustment

Storage Procedures

Troubleshooting

Fault Code Resolution Overview

Engine Troubleshooting

Starter Motor and Alternator Issues

Transmission and Axle System Problems

Steering and Hydraulic System Issues

Attachment Troubleshooting

Specifications

Engine and Powertrain Specifications

Brakes, Controls, and Hydraulics

Bucket and Tire Specifications

Dimensions and Performance Data

Accessories

Loader Attachment Quick Couplers