Newall E70 - User Manual

E70 Quick Start up Guide
Technical Specification
N
For the complete manual please download from:
http://newall.com , Click technical Support to access the download
page.
Environmental
Operating Temperature Storage Temperature
0 to 45°C -20 to 60°C
Environmental Conditions - indoor use, IP20 (IEC 529)
Relative Humidity - maximum 80% for temperature up to 31°C
decreasing linearly to 33% at 45°C
Transient overvoltage according to INSTALLATION CATEGO-
RY II of IEC664
Pollution Degree 2 in accordance with IEC664
Disposal
At the end of it’s life, you should dispose of the E70 in a safe
manor applicable to electronic goods.
The case work is suitable for recycling. Please
consult local regulations on disposal.
A full hard copy of the manual is available free of charge on request
023-81340/0
DSU Connections
Electrical
EMC and Low Voltage Compliance
BS EN 61000-6-4:2001
BS EN 61000-6-2:2001
BS EN 61010-1:2001
Operating Voltage
100 - 240V
Supply Voltage Fluctuation
not to exceed 10% of operating voltage
Supply Frequency
50 to 60Hz
Maximum Power Consumption
18VA
IEC Inlet (Mains Supply)
Cabinet equipotential terminal
for grounding to machine
Mains supply fuse
Input connectors 2 or 3
according to model
HEAD OFFICE
Newall Measurement Systems Ltd.
Technology Gateway, Cornwall Road
South Wigston
Leicester LE18 4XH
United Kingdom
Telephone: +44 (0)116 264 2730
Facsimile: +44 (0)116 264 2731
Email: sales@newall.co.uk
Web: http://newall.com
Newall Electronics, Inc.
1778 Dividend Drive
Columbus, OH 43228
Telephone: +1 614 771 0213
Toll Free: 800.229.4376
Facsimile: +1 614 771 0219
Email: sales@newall.com
Web: http://newall.com
Note: Newall Measurements Systems reserves the right to change specifications without notice.
Warnings
On / off Switch
The mains supply is connected through a detachable supply cord supplied. If another supply cord is
used, it must have fitted a IEC320, 10A, EARTHED mains connector with a cord rated for at least 10A.
The PROTECTIVE EARTH CIRCUIT of the mains supply MUST BE CONNECTED to the protective earth
terminal of the cabinet through the supply cord.
If a mains plug is not already fitted to the supply cord or is of the wrong type, then a suitable EARTHED
plug should be used which complies with the relevant specifications for plugs and socket-outlets.
The mains supply fuse is a 20x5mm, type T0 .5A, 250v, Disconnect mains before replacing fuse.
The mains supply must be removed before opening the unit and completed by qualified personnel.
Auxillary connection (optional)
Connection to the display
(Cable supplied)

Summary

Safety Warnings for NEWALL E70

Mains Supply Connection and Earth

Details mains supply connection and protective earth requirements for safe operation.

Mains Plug and Fuse Guidance

Specifies correct mains plug type and fuse rating for the unit.

Unit Opening and Maintenance Safety

Warns about opening the unit and requires qualified personnel for maintenance.

Technical Specifications Overview

Environmental Operating Conditions

Lists operating/storage temperature, humidity, and environmental conditions.

Electrical Compliance and Ratings

Covers EMC, Low Voltage, voltage, frequency, and power consumption.

Product Disposal Instructions

Provides guidance on safe end-of-life disposal of the E70 unit.

DSU Connections Diagram

DSU Connection Layout

Illustrates the connections for DSU ports, display, and mains supply.

Understanding the Keypad

Keypad Layout and Axis Controls

Explains the main keypad layout, axis selection, and numeric keys.

Lathe and Mill Specific Keys

Details specialized keys for lathe and mill functions like Taper, PCD, ARC.

Special Function Key Descriptions

Describes functions like absolute/incremental modes, inch/mm display, and tool use.

Setting Up the Unit

Entering Setup and Default Modes

Guides on how to access setup menus and select default configurations.

Optional Settings and Encoder Matching

Covers advanced optional settings and matching encoders for axis setup.

Axis Preset Configuration

Instructions for presetting individual axes, like X, Y, or Z, to default values.

Newall E70 Specifications

General

Brand	Newall
Model	E70
Category	Measuring Instruments
Language	English