What to do if the Nilfisk-ALTO NEPTUNE 5 FA 107400337 C flame sensor is sooted?
If the flame sensor on your Nilfisk-ALTO Pressure Washer is sooted, clean the flame sensor. Cold water operation is possible.
What to do if the Nilfisk-ALTO NEPTUNE 5 FA 107400337 C Pressure Washer motor overheated?
If the motor of your Nilfisk-ALTO Pressure Washer overheats: * Turn the main switch to the OFF position and let the machine cool down. * Remove any extension cords being used. * Have the electrical connections checked for possible phase failure.
What to do if the Nilfisk-ALTO Pressure Washer is leaking or operating in an inadmissible condition due to short-time operation?
If your Nilfisk-ALTO Pressure Washer is leaking or experiences inadmissible operation due to short-time use: * After three short-time operations, the machine will switch off. To reset it, turn the main switch to the OFF position, then start it again, keeping the trigger squeezed for longer than 3 seconds. The machine will switch off if a leak in the hose and gun causes it to start and stop briefly three times. * Repair the spray gun. * Replace the high-pressure hose and retighten the screw fittings. * Fill the detergent tank or set detergent metering to OFF. * Clean the filter. * Repair any leaks.
What to do if the Nilfisk-ALTO Pressure Washer has a water supply issue?
If your Nilfisk-ALTO Pressure Washer has a water supply issue: * Ensure the required volume flow and pressure are as specified in the Technical Data. * Fill the detergent tank or set detergent metering to OFF. * Turn the twist grip on the safety control block to increase water pressure/volume.
What to do if the Nilfisk-ALTO Pressure Washer has a fuel shortage?
If your Nilfisk-ALTO Pressure Washer has a fuel shortage, fill the fuel tank. Cold water operation is possible.
What to do if the Nilfisk-ALTO NEPTUNE 5 FA 107400337 C Pressure Washer pump oil is low?
If the pump oil in your Nilfisk-ALTO Pressure Washer is low, fill it to the proper level.
General| Brand | Nilfisk-ALTO |
|---|---|
| Model | NEPTUNE 5 FA 107400337 C |
| Category | Pressure Washer |
| Language | English |
Explains the intended use and applications of the high-pressure cleaner for professional tasks.
Identifies and describes the various controls, indicators, and components of the machine.
Details procedures for safely moving and assembling the cleaner, including lifting points.
Instructions for engaging the machine's brake to ensure stability during operation or parking.
Guide for attaching the crank handle for managing the high-pressure hose or cord reel.
Instructions for filling detergent tanks A and B with prediluted cleaning agents.
Procedure for filling the anti-scale reservoir with the specified water softener solution.
Information on the antiscale dosing system and how to adjust for water hardness.
Steps for safely filling the fuel tank with appropriate fuel, considering temperature effects.
Instructions for connecting the high-pressure hose to the machine, with different procedures for reel/no reel models.
Procedure for connecting the machine to a water source, including hose and pressure requirements.
Steps for safely connecting the machine to the electrical power supply, including voltage checks.
Instructions for applying antifreeze to protect the machine against freezing before initial operation.
Details on connecting accessories, specifically the spray lance to the spray gun.
Step-by-step guide to starting the high-pressure cleaner for cold, hot water, and steam operation.
Procedure for operating the cleaner in steam mode, including temperature and safety precautions.
How to adjust water pressure using the twist grip on the Tornado Lance unit.
Method for adjusting water volume using the twist grip on the VarioPress Gun.
Instructions for selecting detergent type and percentage for effective cleaning tasks.
Guidelines for efficient high-pressure cleaning, covering soaking, detergent use, and temperature.
Examples of cleaning tasks for agriculture, vehicles, and buildings with recommended accessories.
Cleaning methods for general surfaces, metallic equipment, and rusted areas using specific techniques.
Procedure for safely shutting down the high-pressure cleaner by turning off the main switch.
Steps for safely disconnecting water and power supply after operation.
Instructions for managing the power cord and safely storing accessories like the spray lance.
Procedure for storing the cleaner to prevent freeze damage, including antifreeze use.
Overview of recommended maintenance tasks, including weekly, operating hours, and as required checks.
Detailed procedures for specific maintenance tasks like filter checks, oil changes, and sensor cleaning.
Troubleshooting guide for error codes displayed on the machine, with causes and remedies.
Interpretation of warning and status lights on the control panel, with causes and remedies.
Common operational faults not indicated on display/lights, with their causes and remedies.
Information on environmentally sound disposal of old electrical appliances and equipment.
Details on the warranty coverage, terms, and conditions for the machine and its components.
Official statement of compliance with relevant EU directives for the product.
Comprehensive specifications and technical details for different models of the high-pressure cleaner.
To Next Page