ninjakitchen.com
ninjakitchen.com
1 Remove all packaging materials from the unit. Exercise care when unpacking blade assembly, as the
blades are sharp.
2 The Stacked Blade Assembly is NOT locked in place in the container. Handle the Stacked Blade
Assembly by grasping the top of the shaft.
3 Wash container, lid, and blade assembly in warm, soapy, water using a dishwashing utensil with a
handle to avoid direct contact with the blades. Exercise care when handling blade assembly, as the
blades are sharp.
4 Thoroughly rinse and air-dry all parts.
5 Wipe control panel with a soft cloth. Allow it to dry completely before using.
BEFORE FIRST USE
IMPORTANT: Review all warnings at the beginning of this Owner’s Guide before proceeding.
NOTE: All attachments are BPA free and dishwasher safe. It is recommended that the container, lid, and
blade assembly be placed on the top rack of the dishwasher. Exercise care when handling blade assembly.
ORDERING REPLACEMENT PARTS
To order additional parts and attachments, visit ninjaaccessories.com.
USING THE TOTAL CRUSHING® PITCHER
NOTE:
• If the unit is plugged in and powered on, but the pitcher is not installed, the LEDs on the control
panel will flash.
• Auto-iQ® programs have pauses and changes in speed throughout the cycle.
• DO NOT add ingredients before completing installation of the Stacked Blade Assembly.
• If the Stacked Blade Assembly is not fully seated, you will not be able to install and lock the lid.
• The pitcher lid handle will not fold down unless it is attached to the pitcher.
IMPORTANT:
• Review all warnings at the beginning of this Owner’s Guide before proceeding.
•
As a safety feature, if the pitcher and lid are not properly
installed,
the motor will be disabled. If this
happens, repeat step 5 on the following page. When the pitcher and lid are properly installed, the
program button LEDs will illuminate, indicating the appliance is ready to use.
1 Plug in motor base and place on a clean, dry, level surface such as a
countertop or table.
2 Lower the Total Crushing Pitcher onto the motor base. The handle should
be aligned slightly to the right and the pitcher should be oriented so
the LOCK symbols are visible on the motor base. Rotate the pitcher
clockwise until it clicks into place.
3 Exercising care, grasp the Stacked Blade Assembly by the top of the shaft and
place it onto the drive gear inside the pitcher. Note that the blade assembly will
fit loosely onto the drive gear.
4 Add ingredients to the pitcher. DO NOT add ingredients past the MAX LIQUID
line on the pitcher.
5 Place the lid on the pitcher, aligning the triangle symbol on the lid with the triangle
symbol on the handle. Press down on the handle until it clicks into place. The
triangle symbols MUST be aligned for the lid to lock and the unit to operate. Once
the lid is locked in place, press the Power button to turn unit on. The available
program buttons will illuminate and the unit will be ready for use.
6a If using an Auto-iQ® program, first select the program that best suits your
recipe. The preset feature will automatically stop at the end of the program.
To stop the unit at any time, press the currently active button again.
6b If using a manual program, select your desired speed. Once the ingredients
have reached your desired consistency, press the active button again, or wait
for the unit to come to a complete stop after 60 seconds.
7 To remove the pitcher from the motor base, turn the pitcher counterclockwise and
then lift up.
8b For thicker mixtures that cannot be emptied through the pour spout, remove
the lid and Stacked Blade Assembly before pouring. To remove the lid, press the
RELEASE button and lift the handle. To remove the blade assembly, carefully grasp
it by the top of the shaft and pull straight up. The pitcher can then be emptied.
8a To pour out thinner mixtures, ensure the lid is locked in place, then open
the pour spout cap.
9 Turn the unit o by pressing the Power button. Unplug the unit when
finished. Refer to the Care & Maintenance section for cleaning and
storage instructions.
To Next Page
Loading...
Need help?
General