Nordyne 096C-16 User Manual

Installation Instructions
Do not store or use gasoline
or other flammable vapors
and liquids in the vicinity of
this or any other appliance.
DO NOT DESTROY. PLEASE READ CAREFULLY AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.
FOR YOUR SAFETY
WARNING:
Improper installation,
adjustment, alteration,
service, or maintenance can
cause injury or property
damage. Refer to this
manual. For assistance or
additional information
consult a qualified installer,
service agency, or the gas
supplier.
These instructions are primarily intended to assist qualified individuals experienced in the proper installation of this
appliance. Some local codes require licensed installation/service personnel for this type of equipment. Read all
instructions carefully before starting the installation.
FOR YOUR SAFETY
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any
appliance.
• Do not touch any electrical
switch; do not use any
phone in your building.
• Immediately call your gas
supplier from a neighbor's
phone. Follow the gas
supplier's instructions.
• If you cannot reach your gas
supplier, call the fire
department.
• Extinguish any open flame.
80+ High Efficiency Upflow/Horizontal and Downflow
with Variable Speed Blower
Residential Gas Furnaces
!
*RK 80+ Downflow
*RA 80+ Upflow

Nordyne 096C-16 Specifications

General

Model Number	096C-16
Category	Furnace
Input BTU	96, 000
Heat Exchanger Material	Aluminized Steel
Warranty	10-Year Limited
Stages	1

Summary

Safety Information

General Safety Precautions

General safety warnings for installation, operation, and gas leak procedures.

Installation Requirements

Requirements and Codes

Outlines compliance with national and local building codes, NFPA, and CSA standards.

Clearances to Combustibles

Specifies minimum clearances from the furnace to combustible materials for safe installation.

Venting and Combustion Air Requirements - General

General Provisions

General provisions for supplying adequate air for combustion and venting requirements.

Venting and Combustion Air Requirements - Clearances

Installation Clearances

Venting Requirements - General

General Venting Requirements

Venting Requirements - Category III

Carbon Monoxide Hazard

Hazard warning and procedures for testing venting systems to prevent carbon monoxide poisoning.

Circulating Air Supply

Gas Supply and Piping

General Gas Supply and Piping

Procedures for connecting gas supply lines, emphasizing compliance with codes and utilities.

Gas Supply and Piping - Checks and Conversions

Leak Check Procedures

Instructions for safely checking gas piping connections for leaks using approved methods.

High Altitude Application

Guidance on adjusting manifold pressure and orifices for high-altitude operation.

Conversion to LP/Propane

Procedures and warnings for converting the furnace from natural gas to LP/propane.

Electrical Wiring - General

General Electrical Wiring

Requirements for making electrical connections, grounding, and wire replacement.

Electrical Wiring - Voltage and Orifices

Line Voltage Wiring

Electrical Wiring - Low Voltage

Low Voltage Wiring

Start-up & Adjustments - Initial Steps

General Start-up Verification

Pre-start-up checks including power, wiring, gas pressure, and safety switches.

Start-Up Procedures

Step-by-step guide for initiating furnace operation and verifying sequence.

Start-up & Adjustments - Firing and Airflow

Verifying and Adjusting Firing Rate

Procedure to measure and adjust the furnace firing rate to prevent over-firing.

Configuring the Blower

Instructions for configuring the variable speed blower kit using motor control board switches.

Selecting Heat Airflow

Start-up & Adjustments - Cooling Airflow and Temp Rise

Selecting The Cooling/Heat Pump Airflow

Verifying and Adjusting Temperature Rise

Procedure to verify and adjust the temperature rise across the furnace.

Start-up & Adjustments - Operation Verification

Verifying Burner Operation

How to check burner ignition, flame characteristics, and operation.

Verify Operation of the Supply Air Limit Switch

Procedure to test the function of the supply air limit switch.

Wiring Diagram

Maintenance - General

Vent System Maintenance

Air Filter Maintenance

Heat Exchanger and Burner Maintenance

Maintenance - Flue Passages

Cleaning Of Flue Passages

Installation/Performance Checklist