EasyManuals Logo

Nortek DOOR GARD User Manual

Nortek DOOR GARD
4 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
6-050212 X2 1
Features and Programming Guide
PRINTER’S INSTRUCTIONS:
LIT 212 PROGRAMMING GUIDE - P/N: 6-050212 X2 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: FLAT 17.000” X 11.000” FOLDED 8.500” X 11.000” - TOLERANCE: ± .125” - SCALE: 1-1
FEATURES
4 INDEPENDENT OUTPUTS
4 INDEPENDENT TIMERS
ALL OUTPUTS ASSIGNABLE BY CODE
ON BOARD MAIN RELAY
120 USERS
REMOTE TRIGGERING INPUT
KEYPAD PROGRAMMABLE
MEMORY
Non-volatile EEPROM memory means your codes and
instructions will be there whether you remove power for
5 minutes or 5 years.
PROGRAMMING
All programming is done entirely from the front of the
keypad. LED or sounder guidance makes programming
easy. It takes seconds for an authorized user to change
codes.
CODES
The DoorGard keypads allow up to 120 individual user
codes. Codes can be 1 to 6 digits in length and digits may be
repeated. The Master Code is always stored in user location
one (1).
MAIN RELAY
The main relay is a form C relay, which you can program as
a timed output (1 to 90 seconds) or to toggle (latch). See the
Wiring Diagram and Speci cations for the relay electrical
speci cations.
AUXILIARY OUTPUTS
You can program these outputs as timed outputs (1 to
90 seconds) or to toggle (latch). They can be controlled
individually or in combination by a code. Some models
have 1 Amp form C relays and other models have negative
voltage outputs with a 50mA sink.
PANIC
Panic is activated by pressing the and # keys at the same
time. By default, it operates output 4 and activates for 1
second.
REMOTE TRIGGERING INPUT (REX)
By default, upon a momentary closure this normally open
loop triggers the main relay for the same time period as the
Master Code. You can also program the REX to operate any
combination of the available outputs. The auxiliary outputs
activate for their programmed time.
KEYPRESS FEEDBACK/AUDIBLE KEYPRESS
DoorGard keypads, by default, acknowledge a keypress
by momentarily illuminating the yellow LED or activate the
sounder. This depends on the model. You can turn this off
through programming.
KEYPAD ACTIVE OUTPUT
DoorGard keypads can be programmed to energize a
voltage output whenever a key is touched. You can use this
to turn on lights, CCTV camera, or notify a guard.
AUTO ENTRY
This feature is used when you don’t want to press the key
after entering your code. You only need to enter your code
number (without pressing ) and the relay activates. To
use this feature, the user codes must be the same length
as the master code. Please remember to access program
mode when auto entry is on, do not press the key (Press:
99 # master code), however the is required while entering
programming commands.
Voltage Outputs may be converted to 1 Amp, Form-C
relays by adding the 293 Auxiliary Relay Board (Model
# 0-219000).
DOORGARD keypads offer eld proven reliability and cost effective solutions anywhere limited control or access is desired.
Designed for individual control of up to four devices, DoorGard keypads are the perfect choice for controlling electric locking
devices, security systems, automatic operators or machinery. DoorGard keypads accept power from a 12 or 24 Volt AC/DC
supply.
Access Control Keypads
Features and Programming Guide
Note: This product is designed to be installed and serviced
by security and lock industry professionals.

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Nortek DOOR GARD and is the answer not in the manual?

Nortek DOOR GARD Specifications

General IconGeneral
BrandNortek
ModelDOOR GARD
CategoryKeypad
LanguageEnglish

Related product manuals