NXP Semiconductors
UM12018
FRDM-MCXN947 Board User Manual
Pin
number
GPIO Function Potential conflict
7 P1_5 EZH_LCD_D1_CAMERA_D1 LAN8741 Ethernet PHY (P1_5/ENET_TXEN
through R160 zero-ohm resistor)
8 P1_4 EZH_LCD_D0_CAMERA_D0 LAN8741 Ethernet PHY (P1_4/ENET_TXCLK
through the resistor SJ27 Pin 1-2 selection
(default setting))
9 P1_7 EZH_LCD_D3_CAMERA_D3 LAN8741 Ethernet PHY (P1_7/ENET_TXD1
through R162 zero-ohm resistor)
10 P1_6 EZH_LCD_D2_CAMERA_D2 LAN8741 Ethernet PHY (P1_6/ENET_TXD0
through R161 zero-ohm resistor)
11 P3_5 EZH_LCD_D5_CAMERA_D5 -
12 P3_4 EZH_LCD_D4_CAMERA_D4 -
13 P1_11 EZH_LCD_D7_CAMERA_D7 • I3C sensor device (P1_11/I3C1_PUR
through R169 zero-ohm resistor)
• CAN PHY (P1_11/CAN0_RXD through
the resistor SJ26 Pin 1-2 selection (default
setting))
14 P1_10 EZH_LCD_D6_CAMERA_D6 • CAN PHY (P1_10/CAN0_TXD through the
resistor SJ16 Pin 1-2 selection (default
setting))
• Arduino connector J4 pin 11 (P1_10/TSI0_
CH19-HDR through the resistor SJ20 Pin
2-3 selection (DNP by default))
15 P0_5 EZH_CAMERA_PCLK • Pmod connector pin 4 (P0_5/PDM0_DATA0
through the resistor SJ13 Pin 2-3 selection
(DNP by default))
• Arduino connector J4 pin 9 (P0_5/TSI0_
CH9 through the resistor SJ21 Pin 2-3
selection (DNP by default))
16 P2_2 CAMERA_CLKIN SDHC connector (P2_2/SDHC0_D1)
17 P0_4 EZH_CAMERA_VSYNC • Pmod connector pin 6 (P0_4/PDM0_CLK
through the resistor SJ12 Pin 2-3 selection
(DNP by default))
• Arduino connector J4 pin 5 (P0_4/TSI0_
CH8 through the resistor SJ22 Pin 2-3
selection (DNP by default))
18 P0_11 EZH_CAMERA_HSYNC -
19 P3_3 FC7_I2C_SCL -
20 P3_2 FC7_I2C_SDA -
21 - P3V3 -
22 - GND -
23 P1_23 EZH_LCD_RD Arduino connector J1 pin 8 (P1_23/ARD_
D3 through the resistor SJ1 Pin 1-2 selection
(default setting))
24 P1_22 EZH_LCD_DC • Arduino connector J3 pin 3 (P1_22/TRIG_
IN3-MC_ENC_A)
Table 24. Camera header connections...continued
UM12018 All information provided in this document is subject to legal disclaimers. © 2024 NXP B.V. All rights reserved.
User manual Rev. 1 — 20 January 2024
29 / 41
To Next Page
Loading...
