EasyManua.ls Logo

Oceanic 0CS30 - User Manual

Oceanic 0CS30
18 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
April ‘13
Oceanic Sauna Heater Manual
Thank you for choosing to buy our Oceanic Sauna heater; please take the time to read
these instructions before you begin as they contain important information about the
installation and maintenance requirements.
“Oceanic” sauna heaters are available in specifications from 3kw to 9kw and are
equipped with our OC-SA digital controller. With this not only can you control the temperature and time
duration of your sauna bath but also the light of the sauna room, alter the temperature display between
Centigrade and Fahrenheit; as well as displaying the sauna heater’s status.
Every “Oceanic” sauna heater is thoroughly tested before leaving the factory.
IMPORTANT
• Read the manual before installation and operation and then keep it for reference
• This equipment must be installed by competent person
• This equipment must be connected to an all pole isolator of the correct rating
• Disconnect the power supply before exposing electrical connections
• All heaters can be connected single phase(230v) or triple phase(400v), this can be easily changed by
adding bridge connectors across the connections L1, L2 and L3.
• 5 core silicon bound heat proof cable must be used to wire from the control to the heater. (For 230v and
400v) Wire the letters with the corresponding letters on the heater. For example: U V W on the control
go to U V W on the heater, the three lives for the elements, the reason for having three is because each
element is controlled individually. When the heater reaches the desired temp it cuts out two elements.
• The sauna heater should not be used for any other purpose
• Do not cover the heater or allow contact with flammable materials such as toweling – Risk of fire.
• Do not operate sauna heater without sauna stone
• Do not touch the heater when operational as it is very hot
• Sauna heater must have right earth connection, the earth wire should be bigger than the power supply
wire to sauna heater
• The sauna controller should be installed on a dry wall outside the sauna cabin

Table of Contents

Questions and Answers

  • M
    Michelle TorresAug 16, 2025
    Why does the Oceanic Heater temperature window display '--Lo' or '--Ho'?
    • C
      Christine TurnerAug 16, 2025
      The temperature window on your Oceanic Heater might display '--Lo' or '--Ho' due to several reasons: * If it displays '--Lo,' it could mean the temperature sensor isn't connected, the cable is broken, or the temperature is below 0°C. Check the connection and cable, or consider changing the sensor. * If it displays '--Ho,' it indicates a short circuit in the temperature sensor or that the temperature exceeds 115°C. Inspect the connection and cable, or replace the sensor. In some cases, you might need to change the controller.
  • J
    Jennifer CaldwellAug 19, 2025
    What to do if the OverHeat LED is on in my Oceanic Heater?
    • H
      Holly JohnsSep 12, 2025
      If the OverHeat LED is illuminated on your Oceanic Heater, it indicates a potential issue with the temperature sensor connection or the high-temperature cut-off switch. First, check the connection to the temperature sensor to ensure it is properly connected. Next, verify if the high-temperature cut-off switch is turned off; if it is, manually reset it.
  • K
    Karen GarciaAug 22, 2025
    What to do if the Oceanic sauna heater controller is on but the sauna heater doesn’t work?
    • R
      Raymond HensonAug 22, 2025
      If the controller of your Oceanic sauna heater is on, but the heater isn't working, there could be a connection problem or an issue with the controller itself. First, check the heater's connection. If the connection is correct, you may need to replace the controller.
  • G
    George NorrisAug 25, 2025
    What to do if the Oceanic 0CS30 Heater 'Wait' LED is red?
    • K
      Kathryn ChavezAug 26, 2025
      If the 'Wait' LED on your Oceanic Heater is red, it means the sauna heater is in B mode. To resolve this, press the Mode button to switch to A mode, which is the heating mode.
  • B
    Billy GreenAug 28, 2025
    How to fix Oceanic Heater when there is no display on the control panel?
    • A
      Alexander AllenAug 28, 2025
      If there is no display on the control panel of your Oceanic Heater when you press the on/off switch, the issue might be with the power supply, the circuit board transformer, or the fuse. Begin by checking the power supply. If the power supply indicator LED L1 (red) is on, inspect the wire. If the power supply is not the issue, consider changing the controller.
  • J
    Joseph NortonAug 31, 2025
    What to do if Oceanic 0CS30 temperature windows display --L or --H?
    • N
      Nicholas WilliamsonAug 31, 2025
      If the temperature windows display '--L' or '--H' on your Oceanic Heater, it indicates a problem with the thermometer or the temperature being outside the measurable range. Specifically: * '--L' means the temperature sensor isn't connected, the cable is broken, or the temperature is below 0°C (32°F). Check the connection and cable, or replace the sensor. * '--H' indicates a short circuit in the temperature sensor or the temperature exceeding 115°C (239°F). Again, inspect the connection and cable, or replace the sensor. If the issue persists, consider changing the controller.
  • C
    carlastevensSep 3, 2025
    Why is the High1 LED on my Oceanic 0CS30 Heater?
    • S
      Shirley HardySep 3, 2025
      If the 'High1' LED is illuminated on your Oceanic Heater, it means that either the temperature sensor isn't properly connected or the high-temperature cut-off switch has been activated. First, check the connection to the temperature sensor. If that's not the issue, verify if the high-temperature cut-off switch is turned off; if it is, manually reset it.
  • A
    arossSep 6, 2025
    What to do if Oceanic 0CS30 Heater controller is on but the sauna heater doesn’t work?
    • M
      Melissa RasmussenSep 6, 2025
      If your Oceanic sauna heater controller is on, but the heater isn't working, it could be due to a couple of reasons. First, ensure that the sauna heater is properly connected, referring to the diagrams in figures 2 and 10. If the connection is correct and the heater still doesn't work, the controller might be faulty, and you may need to replace it.
  • A
    Anna AndersonSep 9, 2025
    How to troubleshoot no display on Oceanic Heater control panel?
    • J
      Jonathan MayerSep 9, 2025
      If there is no display on the control panel of your Oceanic Heater when you press the on/off switch, it indicates a problem with the power supply, the circuit board transformer, or the fuse. Check the power supply first. If the power supply indicator LED L1 (red) is lit, then check the wire. If not, consider changing the controller.
  • C
    Courtney RaySep 12, 2025
    Why is the Wait LED on on my Oceanic 0CS30 and how to fix it?
    • J
      John HowardSep 12, 2025
      If the 'Wait' LED is illuminated on your Oceanic Heater, it signifies that the sauna heater is operating under the B model setting. To resolve this, simply press the Model button to switch to the A model, which is the heating mode.

Oceanic 0CS30 Specifications

General IconGeneral
BrandOceanic
Model0CS30
CategoryHeater
LanguageEnglish

Related product manuals