OEM Tools 24813 User Manual

UNPACKING
After unpacking unit, inspect
carefully for any damage that may
have occurred during transit. Check
for loose, missing, or damaged
parts. If any damage is observed,
a shipping damage claim must be
filed with carrier. Do not use Press
Pin Set if broken, bent, cracked or
damaged parts (including labels)
are noted. Any Press Pin Set that
appears damaged in any way,
operates abnormally or is missing
parts should be removed from
service immediately. If you suspect
that the Press Pin Set was subjected
to a shock load (a load that was
dropped suddenly, unexpectedly,
etc.) immediately discontinue use
until it has been checked by a factory
authorized service center.
Please read and save these instructions. Read through this owner’s manual carefully before using product. Protect
yourself and others by observing all safety information, warnings, and cautions. Failure to comply with instructions
could result in personal injury and/or damage to product or property. Please retain instructions for future reference.
Operating Instructions and Parts Manual 24813
FOR CUSTOMER SERVICE
Technical Question?
CALL 1-866-458-2472
customerservice@oem-tools.com
PRESS PIN SET
Explanation of Safety Signal Words
CAUTION
Notes
CAUTION
WARNING
The following safety information is provided as guidelines to help you operate your Press Pin Set under the safest
possible conditions. Any tool or piece of equipment can be potentially dangerous to use when safety or safe
handling instructions are not known or not followed. The following safety instructions are to provide the user with the
information necessary for safe use and operation. Please read and retain these instructions for the continued safe use
of your service system. Failure to follow instructions listed below may result in serious injury. In addition, make certain
that anyone that uses the equipment understands and follows these safety instructions as well.
WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or
other reproductive harm.
WARNING
: Indicates a potentially hazardous situation which, if not avoided, could result in death or
serious injury.
: Indicates a potentially hazardous situation which, if not avoided, may result in minor or
moderate injury.
: Used without the safety alert symbol indicates a potentially hazardous situation which, if
not avoided, may result in property damage.
: Provide clarity and helpful information.
09/14
2014 ©OEM-TOOLS

OEM Tools 24813 Specifications

General

Type	Impact Wrench
Voltage	20V
Height	8 inches
Drive Size	1/2 inch
Spindle Thread	5/8"-11
Arbor Size	5/8"
Width	3 inches

Summary

Product Introduction and Safety Overview

Unpacking and Initial Inspection

Instructions for unpacking and inspecting the press pin set for damage.

General Safety Guidelines and Warnings

Introduction to safety information and explanation of signal words like WARNING and CAUTION.

Detailed Safety Instructions

Work Area and Personal Safety

Rules for maintaining a safe work area, keeping children away, and personal attire.

Safe Operation Practices

Guidelines on tool usage, avoiding overreaching, and keeping away from flammables.

Tool Maintenance and Servicing

Instructions on checking tool condition, using correct parts, and professional servicing.

Safe Working Environment and Procedures

Maintaining a Safe Workspace

Ensuring a well-lit, clean work area free of obstructions and avoiding damp conditions.

Vehicle Service Safety

Precautions for working on vehicles, including ventilation and engine parts.

Operator Responsibility and Common Sense

Emphasis on operator's understanding, common sense, and basic automotive knowledge.

Product Description and Operation

Product Description

Overview of the 8-piece press accessory kit and its specifications.

Operation Warnings and Safety

Critical warnings about press capacity, overload, and safe operation practices.

Workpiece Handling and Hazards

Guidance on workpiece support, unsafe items, and avoiding projectile injuries.

Advanced Operation and Hazard Avoidance

Correct Tooling and Load Alignment

Importance of correct tooling and procedures for misaligned loads.

Safe Working Zones and Operations

Precautions for safe working zones and avoiding incorrect press operations.

Spring-Back Hazard Mitigation

Anticipating and securing workpieces to prevent spring-back injuries.

Parts List and Maintenance

Press Pin Set Components

Illustrated list of all parts included in the press pin set with descriptions and quantities.

Maintenance Procedures

Instructions for inspecting the press pin set for damage before each use.

Warranty and Contact Information

OEMTOOLS Limited 90 Day Warranty

Details of the warranty coverage, limitations, and return procedures.

Contact Us

Contact information for customer service and company address.