EasyManua.ls Logo

Olimpia splendid SECCO SUPER - User Manual

Olimpia splendid SECCO SUPER
2 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
S
S
S
e
e
e
r
r
r
v
v
v
i
i
i
c
c
c
e
e
e
M
M
M
a
a
a
n
n
n
u
u
u
a
a
a
l
l
l
3
SECCO PIÙ - SECCO SUPER
Display:
Usually the display shows set point, press “Hr” button to see room humidity. Set point can be regulated
between 30 and 90, 5 by 5, pressing UP or DOWN. (only for Secco Super)To select minimum or
maximum fan speed, press the fan button.
Stand by mode:
To start and stop the unit pres Stand By button. In stand by mode every component is off, there is no
measuring and no programming is possible.
Dry mode:
Compressor and fan start if the difference between room humidity and set point is higher than 3 and if a
time higher than “Cf” has passed after last stop. Compressor and fan keep going until the difference
between room humidity and set point is higher than -3. When compressor stops the fan keep going for
another 30 seconds. When the tank is full all components turn off, tank led turns on and the unit buzzes for
15 sec. Pressing one button during the 15 sec the buzz stops.
All inputs are saved in an eeprom, after a power failure the unit will restart considering last inputs.
Defrosting mode:
When there is ice on the evaporator (evaporator temperature < “Ft” and compressor on) the compressor
keep working for another 30 min, than it stops while the fan keep going until evaporator temperature >

Questions and Answers

Summary

Seco Più - Seco Super Operation

Display Functionality

Shows set point and room humidity. Set point adjustable between 30-90, 5 by 5.

Stand By Mode Operation

Turns unit off, no measuring or programming possible. Press Stand By button to activate.

Dry Mode Operation

Compressor/fan start based on humidity difference and time. Auto-off when tank is full.

Defrosting Mode Logic

Activates when evaporator is iced, compressor stops after 30 min, fan continues.

Troubleshooting and Settings

Full Tank Alarm Deactivation

Deactivates full tank alarm by pressing UP+DOWN for 3 sec. Alarm resets when switch closes.

Probe and Temperature Alarms

Handles sensor damage (Hr/tE) and low evaporator temp (LO) alarms.

Self Test Procedure

Initiates unit diagnostics by pressing DOWN+Hr for 3 sec.

Setup Mode Configuration

Allows setting unit parameters by pressing Hr+UP for 3 sec in standby.

Default Parameter Values

Lists default values for compressor time, defrost temp, and stop time.

Summary

Seco Più - Seco Super Operation

Display Functionality

Shows set point and room humidity. Set point adjustable between 30-90, 5 by 5.

Stand By Mode Operation

Turns unit off, no measuring or programming possible. Press Stand By button to activate.

Dry Mode Operation

Compressor/fan start based on humidity difference and time. Auto-off when tank is full.

Defrosting Mode Logic

Activates when evaporator is iced, compressor stops after 30 min, fan continues.

Troubleshooting and Settings

Full Tank Alarm Deactivation

Deactivates full tank alarm by pressing UP+DOWN for 3 sec. Alarm resets when switch closes.

Probe and Temperature Alarms

Handles sensor damage (Hr/tE) and low evaporator temp (LO) alarms.

Self Test Procedure

Initiates unit diagnostics by pressing DOWN+Hr for 3 sec.

Setup Mode Configuration

Allows setting unit parameters by pressing Hr+UP for 3 sec in standby.

Default Parameter Values

Lists default values for compressor time, defrost temp, and stop time.

Overview

  1. Function Description
  2. Usage Features
  3. Maintenance Features
  4. Important Technical Specifications (Default Values)

The document describes the Olimpia Splendid Secco Più - Secco Super dehumidifier, providing a service manual with operational, troubleshooting, and setup information.

Function Description

The Secco Più - Secco Super is a dehumidifier designed to reduce room humidity. It operates by drawing in humid air, passing it over an evaporator to condense moisture, and then expelling drier air. The device includes a compressor and a fan to facilitate this process. It features a display that typically shows the set point, which can be adjusted between 30% and 90% relative humidity in 5% increments (for the Secco Super model). The unit also allows for the selection of minimum or maximum fan speed.

Usage Features

Standby Mode: The unit can be started and stopped using the Stand By button. In standby mode, all components are off, and no measurements or programming are active.

Dry Mode:

  • The compressor and fan activate when the difference between the room humidity and the set point is greater than 3%.
  • There's a "Cf" parameter that dictates a minimum time delay after the last stop before the compressor and fan can restart.
  • The unit continues to operate until the difference between room humidity and the set point is greater than -3%.
  • After the compressor stops, the fan continues to run for an additional 30 seconds to ensure thorough drying.
  • Full Tank Indication: When the water tank is full, all components turn off, the tank LED illuminates, and the unit emits a buzz for 15 seconds. Pressing any button during this 15-second period will stop the buzz.
  • Power Failure Recovery: All user inputs are saved in an EEPROM, allowing the unit to restart with the last settings after a power failure.

Defrosting Mode:

  • This mode activates when ice forms on the evaporator (evaporator temperature falls below "Ft" while the compressor is on).
  • The compressor continues to run for an additional 30 minutes.
  • After this, the compressor stops, but the fan continues to operate until the evaporator temperature rises above "St".
  • If the compressor stops due to the set point being reached while ice is present, the fan will continue until the evaporator temperature is acceptable.

Full Tank Deactivation: The full tank alarm switch can be temporarily deactivated. This is done by pressing the UP + DOWN buttons for 3 seconds when the switch is open (indicating a missing or full tank). The tank LED will blink to confirm this function is active. It automatically deactivates when the switch closes (tank is correctly inserted and not full).

Maintenance Features

Troubleshooting:

  • Probe Alarm: If a sensor is damaged, the unit will buzz for 15 seconds and display "Hr" (humidity sensor) or "tE" (evaporator sensor). An "Hr" alarm can also occur if room humidity drops below 22%, and will clear automatically when humidity rises again.
  • Low Temperature Alarm: If the evaporator temperature remains below "St" after 30 minutes of defrosting, the fan stops, and the unit displays a blinking "LO" with all LEDs off.

Self-Test: To initiate a self-test, press the DOWN + Hr buttons simultaneously for 3 seconds. The unit will then:

  1. Turn off all components and illuminate all LEDs.
  2. Display the software release version.
  3. Turn on the compressor and fan, showing "At".
  4. Allow pressing DOWN to display the evaporator temperature.
  5. Allow pressing Hr to display the relative humidity.
  6. To exit the self-test, press the Stand By button.

Setup Mode: This mode allows for configuration of various parameters. It can only be accessed from standby mode by pressing Hr + UP for 3 seconds.

  • The Hr button is used to cycle through parameters.
  • Hr + UP/DOWN is used to change a parameter's value.
  • Releasing the Hr button sets the value.
  • To exit setup mode, either wait 10 seconds without pressing any buttons or turn the unit off.

Important Technical Specifications (Default Values)

The manual provides a table of default values for key operational parameters:

  • Co (Compressor minimum working time during defrosting): Default value is 30 minutes (range 20-50 min).
  • Cf (Minimum stop time for compressor): Default value is 3 minutes (range 3-15 min). This likely refers to the minimum time the compressor must remain off before restarting.
  • Ft (Evaporator temperature for defrosting): Default value is -1°C (range -9°C to 0°C). This is the temperature threshold at which defrosting is initiated.
  • St (End defrosting temperature): Default value is 3°C (range 0°C to 9°C). This is the temperature at which the defrosting cycle is considered complete.

Olimpia splendid SECCO SUPER Specifications

General IconGeneral
BrandOlimpia splendid
ModelSECCO SUPER
CategoryHumidifier
LanguageEnglish

Related product manuals