OMEX Rev Limiter TWIN COIL - User Manual

OMEX
PERFORMANCE ELECTRONICS
Please ensure that you read this manual thoroughly before you install this unit. In conjunction
with this Rev Limiter, we recommend the use of a high quality shift light, such as the Omex
Shift Light Pro or Sequential.
This Rev Limiter is suitable for most 4-stroke petrol engines and most ignition types, but not
capacitor discharge (CDi) systems or positive earth vehicles. It should only be used to limit
engine revs, never a vehicle’s road speed.
INSTALLATION
Ensure that the ignition is turned off before starting installation.
Remove the backing from the adhesive pad on the back of the unit and mount it to a clean,
flat, grease-free surface. Keep the unit away from hot or exposed areas. Ensure that the
unit and all wires are kept as far as possible from the HT parts of the ignition system.
The unit is connected to the engine using the attached colour coded wires and the supplied
cable connectors.
BLUE WIRE Connect this to the coil negative (-) terminal
RED WIRE Connect this to the coil positive (+) terminal. If this is not easily accessible
then this wire can be connected to any positive feed that is switched by
the ignition switch.
BLACK WIRE Connect this wire to any good electrical connection on the car bodywork.
A self-tapping screw and spring washer are supplied for this purpose if no
bolt heads are within easy reach of the wire. It is essential that a good
quality connection is made.
Keep wires clear of hot or rotating parts using the supplied cable ties.
SETTING UP
The two buttons and LED indicators allow you to set and control all the functions on your
Rev Limiter Clubman. During manufacture, the unit is programmed to the most common
settings. These may be changed by the following procedures:-
‘+’
BUTTON
‘-’ BUTTON
COIL POSITIVE (+)
COIL NEGATIVE (-)
EARTH
RED
EAR
TH
ORANGE
BLACK
BUTTON
BLACK
BLUE
ORANGE
LED 1
LED 2
+
LED 1
LED 2
OMEX
-
CL UBM AN
REV LIMITER
OMEX
PERFORMANCE ELECTRONICS
K
o
K
VER
SION
www.omextechnology.co.uk
OMEX TECHNOLOGY SYSTEMS LTD
3 Mackenzie Way
Manor Road
Cheltenham
GLOS GL51 9TX
T: +44 (0)1242 260656 F: +44 (0)1242 578069
Email: info@omextechnology.co.uk
WITH LAUNCH CONTROL
SINGLE COIL
INSTALLATION
AND
USER INSTRUCTIONS
R
E
V
INNOVATION RESEARCH DESIGN MANUFACTURE QUALITY
72
/245 - 95/54 - 1573 - 00
e
11
E
U
ROPEAN TYPE APPROVED
+
2
1
WITH LAUNCH CONTROL
SINGLE COIL
info@race-shop.sk
WWW.RACE-SHOP.SK
Orange: 0915 44 11 22 O2: 0948 45 15 25

Summary

Installation

Red Wire Connection

Connects to the coil positive (+) terminal or a switched positive feed.

Blue Wire Connection

Connects to the coil negative (-) terminal.

Black Wire Connection

Connects to a good electrical ground on the car bodywork.

Setting Up

Setting the Number of Cylinders

Procedure to set the engine's cylinder count for accurate rev limiting.

Setting Hard; Soft Cut

Configures the engine's rev limit cut-in style (gradual or immediate).

Setting the Rev Limit

Adjusts the maximum engine RPM limit in 100 RPM increments.

Launch Control Setup

Procedure to set the desired launch control RPM limit.

Launch Control Use

Instructions on how to activate and use the launch control feature.

Resetting the Rev Limit

Resets the rev limiter and launch limit to factory default settings.

OMEX Rev Limiter TWIN COIL Specifications

General

Brand	OMEX
Model	Rev Limiter TWIN COIL
Category	Automobile Accessories
Language	English