Omnia 11 Quick Start Installation Guide

NETWORK CONFIGURATION (CONT.) sysTEm CONFIGURATION sysTEm CONFIGURATION (CONT.) QUICK-sTART INsTAllATION GUIdE
OmNIA.11 sTEREO Fm AUdIO PROCEssOR
Items you need to supply:
• RackwithfouravailableEIArackspacesformounting
• Professionalline-levelanalogorAES/EBUdigitalaudio
 sourcesonstandardXLRconnectors
• ConfiguredEthernetswitch
REQUIRED EQUIPMENT, CABLES, AND ACCESSORIES:
Thereareafewadditionalitemsrequiredforasuccessfulinstallation.Checkthelistbelowandmakesure
youhavewhatyouneed.
Included items:
• Omnia.11AudioProcessor
• ACPowercable
• Ethernetcable
• 4rackscrews
WehavemadethisOmniaSystemeasytosetupandconfigure.Thisquick-startguidewilltakeyouthroughthe
basicstepstoconfigureyournewOmnia.11tostartdeliveringcleaner,clearer,louder,andmoreconsistentsound.
Beforewegetstarted,let’smakesureyouhavewhatyouneed.
ThANK yOU FOR PURChAsING ThE OmNIA.11 sTEREO Fm
AUdIO PROCEssOR
CONTINUE TO sysTEm CONFIGURATION
Network configuration is complete. Your system is
readyforsystemconfiguration.Continuetothe“System
Configuration”instructions.
1. Once the system has rebooted, touch the “Setup”
button(S).
2. Touch the Livewire button (T). The Livewire
configurationscreenwillbedisplayed(U).
3. If you do not have a Livewire system, make sure
the 2 Livewire output channels are disabled. The
2 "Enable" buttons (V) will be white if Livewire
is disabled and green when enabled. To disable
Livewire, touch each of the two green "Enable"
buttons(V)toturnthemwhite.
4. If you do have a Livewire system, enable Livewire
bytouchingeachofthetwo"Enable"buttons(V)to
turnthemgreen.
5. IfyouhaveaLivewiresystem,touchthewhitefields
(W) next to the Output #1 and #2 and enter the
appropriatechannelvalueviathepop-upkeyboard(X).
6. Touchthe“APPLY”button(Y)undertheOutputs.
7. Touchthewhitefields(Z)nexttotheInput#1and#2
toentertheappropriatechannelvalueviathepop-
upkeyboard(X).
8. Touchthe“APPLY”buttonundertheInputs(AA).
lIVEWIRE CONFIGURATION
OUTPUT CONFIGURATION
1. Touchthe“Output”icon(II).TheOutputConfigurationscreenwillbedisplayed.Ifthe“Basic”tabisnot
active,touchtoselectit.
INPUT CONFIGURATION
1. Touchthe“ADJ”icon(BB)toreturntotheinitialSystemscreen.
2. Touchthe“Input”icon(CC).TheInputConfigurationscreenwillbedisplayed.Ifthe“Basic”tab(DD)
isnotactive,touchtoselectit.
3. Fromthe“InputSource”drop-down(EE),selecttheAnalog,AES/EBUorLivewireinputasappropriate
foryourinstallation.Ifyouraudiosourceisprovidinganaudiofeedyoushouldseemeteractivityon
thebargraphmeters(FF).
4. Whiledrivingtheinputswithtypicalprogrammaterialatnormaloperatinglevel,adjustthe
appropriate“Master”InputGaincontrol(GG)foryourinstallationuntilthepeak-readinginputbar
graphmetersarereadingjust“intotheyellow”(about–15to–12dBFSorso).Iftheleft/rightaudio
levelscomingintotheOmnia.11aresomewhatunbalanced,youcanadjustthe“RightTrim”control
(HH)tochangetheleveloftherightchannelaloneoveralimitedrange.
©
2016TLSCorp.,AllRightsReserved.
1490-00099-001—QUICKSTARTGUIDE:OMNIA.11C16/15035
yOUR sETUP Is COmPlETE!
That’sit!YouarenowreadytoexperiencetheOmnia.11
forsoundlikeneverbefore.
1. Touchthe“FMOptions”button(JJ)ontheleftsideofthe
MenuAreaandensurethatthePre-Emphasis,Diversity
Delay(ifpresent)andBS-412settings arecorrectfor
yoursystemandyourlocation.
2. Touch the appropriate button (KK) above the “FM
Options”buttontoselectthegroupofoutputcontrols
fortheoutputyouwillbeusing.Alloutputsareactive
simultaneously. Note: If you are using a conventional
AES/EBU L/R digital output to feed an FM exciter or
linearSTL,touchthe“AES/EBU”buttonandbesurethe
“OutputSelection”issetto“FM”andthe“De-emphasis”
isturned“OFF”fortheoutputbeingused.Foraccessto
thecompositeMPXstereogeneratoroutputleveland
stereo pilot controls, touch the “Composite” button.
Note that these controls simultaneously adjust the
OmniaDirectoutput levelsaswell.Finally,adjust the
appropriatecontrolsothatthepeakoutput/modulation
level is correct for the equipment that follows the
Omnia.11.
3. Touchthe“FM”iconbutton(LL)atthetopofthescreen
andthentouchthe“Preset”tab(MM)todisplaythelist
offactoryprocessingpresets.Ifthepresetlistislocked
(grayed-out),touchthe“padlock”icontounlockit.Once
unlocked,simplytouchthedesiredpresetnameinthe
listanditwillbeputdirectly“ontheair".Werecommend
listening to all factory presets to get a feel for their
differencesandthenselectonetostartwith.
4. Touch the “Quick Setup” tab (NN) and adjust the
followingcontrolstosetthebasicloudness,bassand
brightnesssounddesired.
5. Adjust the “Clipper Drive” control (OO) as low as
possible for the loudness needed. This controls the
primaryloudnessvs.distortiontradeoff.Turningitup
makes the sound louder (but more distorted) while
turning it down makes the sound cleaner but not as
loud.Itshouldalwaysbesetaslowaspossibleforthe
levelofloudnessrequired.
6. Settheoverallamountofbassusingthe“Bass”control
(PP). At higher settings of the “Bass Thump” (QQ)
control,the “kick” or “Thump”actionofbassmaterial
isemphasized.
7. Set the basic brightness of a preset by using the
“Presence” (RR), “Treble” (SS) and “Sparkle” (TT)
controls.Notethatthesethreecontrolsonlyboostthe
brightness.Asettingof“0.0”is“flat”ortheminimum
amount of boost for the particular preset that is
currently selected. Reducing brightness can be done,
foroneexample,by reducingthehigherbandsofthe
AGCorLimitermixers.
T
S
U
Z
AA
VW
Y
X
II
KK
JJ
LL
MM
BB
CC
DD
GG
HH
EE
FF
NN
OO
PP
RR
QQ
SS TT

Omnia 11 Specifications

General

Brand	Omnia
Model	11
Category	Recording Equipment
Language	English