Omron Z - Page 14

F-170 General-purpose Basic Switch Z
Note: 1. Do not use the M12 mounting screw and the case mounting hole at the same time, or excessive pulling force will be imposed on the
Switch and the case and cover may be damaged.
2. On the model Z-15GQ3-B, PT can be set to a value larger than that for the Z-15GQ.
3. On the model Z-15GQ8-B, operating position can be adjusted by providing a screw in the plunger section.
The M3 hole with a depth of 10 mm is a through hole. Take precautions so that no water or screw lock agent penetrates into the hole.
Note: Do not use the M12 mounting screw and the case mounting hole at the same time, or the case may be damaged.
Z-15GQ-B Z-15HQ-B Z-15EQ-B Z-01HQ-B Z-10FQY-B Z-15GQ3-B Z-15GQ8-B
OF
RF min.
PT max.
OT min.
MD max.
2.45 to 3.43 N
{250 to 350 gf}
1.12 N {114 gf}
0.4 mm
5.5 mm
0.05 mm
1.96 to 2.79 N
{200 to 285 gf}
1.12 N {114 gf}
0.3 mm
5.5 mm
0.025 mm
6.13 to 7.85 N
{625 to 800 gf}
1.12 N {114 gf}
0.8 mm
5.5 mm
0.13 mm
2.45 N {250 gf}
max.
0.78 N {80 gf}
0.5 mm
5.5 mm
0.05 mm
4.46 to 7.26 N
{455 to 740 gf}
1.12 N {114 gf}
0.8 mm
5.5 mm
0.1 mm
2.45 to 3.43 N
{250 to 350 gf}
1.12 N {114 gf}
4.2 mm
2.5 mm
2.2 mm
2.45 to 3.43 N
{250 to 350 gf}
1.12 N {114 gf}
0.5 mm
5.5 mm
0.05 mm
OP 21.8±0.8 mm 18.8±0.8 mm 32.5±1 mm
Z-15GQ22-B Z-15HQ22-B Z-15EQ22-B Z-10FQ22Y-B
OF
RF min.
PT max.
OT min.
MD max.
2.45 to 3.43 N
{250 to 350 gf}
1.12 N {114 gf}
0.4 mm
3.58 mm
0.05 mm
1.96 to 2.79 N
{200 to 285 gf}
1.12 N {114 gf}
0.3 mm
3.58 mm
0.025 mm
6.13 to 7.85 N
{625 to 800 gf}
1.12 N {114 gf}
0.8 mm
3.58 mm
0.13 mm
4.46 to 7.26 N
{455 to 740 gf}
1.12 N {114 gf}
1 mm
3.55 mm
0.1 mm
OP 33.4±1.2 mm
4.2
+0.075
−0.025
23.3±0.25
PT
OP
15.5
16.3
25.4±0.1 11.9
49.2
9.2
17.45±0.2
Panel Mount Roller Plunger
4.2
+0.075
dia. hole
−0.025
12.7 dia. × 4.8 (stainless-steel roller)
4.36
+0.1
dia.
−0.05
16 dia.
Z-15GQ22-B, Z-15EQ22-B
Z-15HQ22-B, Z-10FQ22Y-B
(See
note)
Two hexagonal nuts (3 t × 17
width across flats)
M12 × 1 mount-
ing screw
Note: Imperfect screw part with a
maximum length of 1.5 mm.
4.2
+0.075
−0.025
9.2
17.45±0.2
PT
OP
15.5
16.3
25.4±0.1 11.9
49.2
23.3±0.25
Panel Mount Cross Roller Plunger
4.2
+0.075
dia. hole
−0.025
12.7 dia. × 4.8 (stainless-steel roller)
4.36
+0.1
dia.
−0.05
16 dia.
Z-15GQ21-B, Z-15HQ21-B,
Z-15EQ21-B
(See
note)
Two hexagonal nuts (3 t × 17
width across flats)
M12 × 1 mount-
ing screw
Note: Imperfect screw part with a
maximum length of 1.5 mm.