Omron Z - Page 16

F-172 General-purpose Basic Switch Z
Note: The AC rating is 10 A at 125 or 250 V.
Z-15GW-B Z-15HW-B Z-15GW32-B Z-10FWY-B Z-15GW3-B
OF max.
RF min.
OT min.
MD max.
0.69 N {70 gf}
0.14 N {14 gf}
5.6 mm
1.27 mm
0.66 N {67 gf}
0.14 N {14 gf}
5.6 mm
0.63 mm
1.47 to 1.96 N
{150 to 200 gf}
0.92 N {94 gf}
5.6 mm
1.27 mm
0.88 N {90 gf}
0.14 N {14 gf}
5.6 mm
2.4 mm
0.78 N {80 gf}
0.15 N {15.5 gf}
4.8 mm
1.12 mm
FP max. 28.2 mm 27.4 mm 28.2 mm 29.8 mm 27.2 mm
OP 19±0.8 mm
OF max.
RF min.
PT max.
OT min.
MD max.
274 mN {28 gf}
34.3 mN {3.5 gf}
10 mm
5.6 mm
1.27 mm
OP 19±0.8 mm
OF max.
RF min.
PT max.
OT min.
MD max.
58.8 mN {6 gf}
4.90 mN {0.5 gf}
19.8 mm
10 mm
2 mm
OP 19.8±1.6 mm
OF max.
RF min.
PT max.
OT min.
MD max.
58.8 mN {6 gf}
4.90 mN {0.5 gf}
8.3 mm
5.6 mm
0.65 mm
OP 19±1 mm
OF max.
RF min.
PT max.
OT min.
MD max.
39.2 mN {4 gf}
2.94 mN {0.3 gf}
10 mm
6 mm
3 mm
OP 20±1 mm
4.2
+0.075
−
0.025
63.5R
26.2
16.9
20.2
25.4±0.1 11.9
49.2
13.9
OP
PT
4.9
9.2
17.45±0.2
Low-force Hinge Lever
Z-15GW4-B
4.2
+0.075
dia. hole
−
0.025
4.36
+0.1
dia.
−
0.05
t = 1 (stainless-steel lever)
4.2
+0.075
−0.025
120R
26.2
16.9
20.2
49.2
25.4±0.1 11.9
13.9
OP
PT
5
2
9.2
17.45±0.2
Z-15HW24-B
4.2
+0.075
dia. hole
−0.025
4.36
+0.1
dia.
−0.05
t = 0.8 (stainless-steel lever)
4.2
+0.075
−0.025
63.5R
20.2
26.2
16.9
25.4±0.1 11.9
49.2
13.9
PT
OP
9.2
17.45±0.2
Low-force Wire Hinge Lever
Z-15HW52-B
4.2
+0.075
dia. hole
−0.025
4.36
+0.1
dia.
−0.05
1 dia. (stainless-steel wire lever)
3 max.
Z-15HW78-B
4.2
+0.075
−0.025
110R
26.2
20.2 16.9
25.4±0.1 11.9
49.2
13.9
PT
OP
9.2
17.45±0.2
Z-15HW78-B
4.2
+0.075
dia. hole
−0.025
4.36
+0.1
dia.
−0.05
1 dia. (stainless-steel wire lever)
3 max.