To Next PageTo Next PageWhy is there no sound coming from my Onkyo HT-S570 Receiver?
If no sound is coming from your Onkyo Receiver, first, ensure the muting function is deactivated. Then, check all connections to the receiver and make sure the input selector is correctly set to the source you're using. Also, disconnect any headphones that are plugged in. Finally, verify that the input signal format is set to 'Auto'.
How to fix an Onkyo HT-S570 Receiver that doesn't switch on?
If your Onkyo Receiver isn't turning on, check the power cord to ensure it's properly connected. If it is, try disconnecting the power cord, waiting a few seconds, and then reconnecting it to address potential external noise interfering with the receiver's circuits.
How do I reset my Onkyo Receiver to factory settings?
To reset your Onkyo Receiver to its factory default settings, hold down the VIDEO 1 button while the HT-R320 is turned on, and then press the STANDBY/ON button.
What to do if the sound of the playback source is not heard on my Onkyo HT-S570 Receiver?
If you're not hearing the sound from your playback source on your Onkyo Receiver, make sure that the appropriate input source is selected.
How to fix a rough or scratchy sound on my Onkyo Receiver?
If you're experiencing rough or scratchy sound with unclear high range on your Onkyo Receiver, use the audio adjust function to cut the treble response, as the treble control may be set too high.
What to do if no picture appears on the TV screen from my Onkyo HT-S570?
If you're not seeing a picture on your TV screen from your Onkyo Receiver, first, make sure your TV is set to receive input from the AV receiver. Check the video cable connections between the receiver and the TV to ensure they are secure. If you're only using an S video connection, also make a standard video connection, then check both the TV's video input and the receiver's output signal.
Why are the buttons on my Onkyo HT-S570 Receiver not working?
If the buttons on your Onkyo Receiver or its remote aren't working, disconnect the power cord, wait a few seconds, and then reconnect it. Power supply fluctuations or static electricity might be interfering with the operation.
Why is there no sound coming from the center speaker of my Onkyo Receiver?
If you're getting little to no sound from the center speaker of your Onkyo Receiver, verify the speaker connections. Note that no sound is reproduced from the center speaker when the listening mode is set to 'Stereo' or 'Orchestra'. Adjust the volume level of the center speaker and check that the selected speaker configuration includes the center speaker.
Why is the subwoofer volume so low on my Onkyo Receiver?
If you're experiencing no sound or very low volume from the subwoofer connected to your Onkyo Receiver, check the subwoofer mode setting to ensure it is not set to 'Off' and is properly configured.
Why is multichannel audio not working on my Onkyo HT-S570 Receiver?
If your Onkyo Receiver isn't outputting multichannel audio, set the input signal format to 'Multich'. Also, ensure the component is connected to the correct DVD jacks (FRONT L/R, SURROUND L/R, CENTER, and SUBWOOFER). Finally, check the DVD player's output settings to ensure it is set for multichannel output, referring to the DVD player's instruction manual for guidance.
General| Channels | 5.1 |
|---|---|
| HDMI Inputs | 4 |
| HDMI Outputs | 1 |
| Speaker Impedance | 6 - 16 ohms |
| Frequency Response | 10 Hz - 100 kHz |
| Input Sensitivity and Impedance | 200 mV/47 kΩ |
| Audio Formats Supported | Dolby TrueHD, DTS-HD Master Audio |
| Total Harmonic Distortion | 0.08% |
| Signal-to-Noise Ratio | 100 dB |
| Audio Inputs/Outputs | Optical/Coaxial Digital Inputs, Analog Audio Inputs, Subwoofer Pre-out |
| Bluetooth | Yes |
Guidelines for optimal speaker placement for surround sound.
Steps to power on the unit and select input sources.
Setting speaker channels and distances.
Adjusting crossover frequency and subwoofer modes.
Manual tuning, auto-tuning, and preset station management.
Explains various surround sound formats and stereo modes.
Selecting modes and operating other AV components.
