Troubleshooting
78
■
The functions System On/Auto Power On and Direct
Change do not work for components connected via RI
r
turned on.
■
When performing Automatic Speaker Setup, the
measurement fails and the message “Ambient noise is
too high.” is displayed.
r
This can be caused by a malfunction in your speaker
unit. Check if the unit produces normal sounds.
■
The display is dark
r
Make sure that Dimmer function is not working. Press
DIMMER button and change the brightness level of the
display.
■
The following settings can be made for the
component video and composite video inputs.
r
While holding down the input selector button
to configure, press HOME once at a time until
the setup, repeat the above described step until
This setting is possible for input selectors assigned
with one of the video inputs "VIDEO 1" to "VIDEO 3" in
"Composite Video Input". If you have a game console
connected to the composite video input, and the picture
is not very clear, you can attenuate the gain.
Video ATT:Off: (Default).
Video ATT:On: (Gain is reduced by 2 dB.)
■
The picture on your TV/monitor connected to the
HDMI output(s) is unstable
r
Try turning the DeepColor function off.
To turn off the DeepColor function, press STB/DVR and
ON/STANDBY on the AV controller simultaneously.
While holding down STB/DVR, press ON/STANDBY
repeatedly until “Deep Color:Off” is appeared on the
display. To reactivate the DeepColor function, repeat the
above described step until “Deep Color:On” appears on
the display.
The AV controller contains a microPC for signal processing
and control functions. In very rare situations, severe
interference, noise from an external source, or static
electricity may cause it to lockup. In the unlikely event that
this happens, unplug the power cord from the wall outlet,
wait at least 5 seconds, and then plug it back in.
Onkyo is not responsible for damages (such as CD rental
fees) due to unsuccessful recordings caused by the unit’s
malfunction.
Before you record important data, make sure that the
material will be recorded correctly.
Before disconnecting the power cord from the wall outlet,
set the AV controller to standby.
Supported Video Resolution of HDMI OUT MAIN/
SUB Jacks
See below the video signal types and resolutions that the
unit can output when it receives the input signals of the
following types and resolutions. The supported resolutions
are shown as "Input: Output".
(North American model)
■
HDMI: HDMI
4K : 4K (
¼
1)
1080p/24 : 4K, 2560 × 1080p
2560 × 1080p : 4K (
¼
2)
1680 × 720p : 4K (
¼
2), 1080p/24, 2560 × 1080p,
1080p/24
1080p : 4K (
¼
3), 2560 × 1080p
1080i : 4K (
¼
3), 2560 × 1080p, 1680 × 720p, 1080p, 720p
720p : 4K (
¼
3), 1080p/24, 2560 × 1080p, 1680 × 720p,
1080p, 1080i
480p : 4K (
¼
3), 2560 × 1080p, 1680 × 720p, 1080p, 1080i,
720p
480i : 4K (
¼
3), 2560 × 1080p, 1680 × 720p, 1080p, 1080i,
720p, 480p
■
HDMI: Component
Cannot be output.
■
HDMI: Composite
Cannot be output.
■
Component: HDMI
1080p : 4K (
¼
3), 2560 × 1080p, 1080p
1080i : 4K (
¼
3), 2560 × 1080p, 1680 × 720p, 1080p, 1080i
720p : 4K (
¼
3), 2560 × 1080p, 1680 × 720p, 1080p, 1080i,
720p
480p : 4K (
¼
3), 2560 × 1080p, 1680 × 720p, 1080p, 1080i,
720p, 480p
480i : 4K (
¼
3), 2560 × 1080p, 1680 × 720p, 1080p, 1080i,
720p, 480p, 480i
■
Component: Component
1080p: 1080p
1080i: 1080i
720p: 720p
480p: 480p
480i: 480i
To Next Page
Loading...
Need help?
General
