I
How
to cancel
memorized stat¡ons
Retrieve the class
number
you
want
to
cancel
(see
"How
to
retrieve.memorized
stations")
and then
press
the
Dl RECT button
while
holding
down the MEMORY
button. Another
station can
be
memorized with the
memory number
which has beén
can-
celled.
I How to retrieve
memorized stat¡ons
@
Press the
Classified
Memory button for the
desired class.
o
The memory
number
(station)
which was last used in the
class will
be received.
@
There are sovoral
methods to
proceed
after
the above opor-
ations are carried out. Use
any of the
following methods.
a.
Pressing the same
Classified Memory button
again
per-
mits
the next
preset
memory
number
(station)
lo be
re-
ceived.
b. lnput the
memoiy number
you
wish to receive
by
using
the
Number buttons.
o
lf
the
memory number consists of
2 digits,
input
two
numbers,
immediately one after the other.
For instance,
when inputting
"15", "15"
will not be
registered if
you
wa¡t more than one second
before inputting
"5",
resulting
in only
"1"
being
registered.
a
lf a number other than a
number
from 1
to
40, or a
number which
has not
been
memorized
is input, the
number
flashes for 2 seconds and then
the number
which was displayed
before will be displayed.
.
lf
a number
between 1 and
4 is
pressed,
the
display
and station are changed 1 second
later.
c. Press the SCAN
button
o
Stat¡ons memorized
in
the
present
class
will be
scanned
in
a
order and the
corresponding
memory
number
will
flash
in
the
Preset
station display at each
scan. After the
last memory
number
of
the class is
reached, scanning
starts again
from
the
first
memory
number of the
class. Pressing the
SCAN button
again
stops scanning.
.
Pressing the SCAN
button
after
pressing
the
MEM-
ORY
button, enables
you
to scan through
the memory
numbers
in all the classes
one by one.
I
APR
(Automat¡c
Precision Reception) System
(FM
only)
This unit
is
equipped
with ONKYO's
unique
APR
system
that
automatically
controls
the Auto stereo/Mono
reception modes,
lF bandwidth
wide/narrow
setting and FM
auto hi-blend circuit
according to the
quality (signal
strength,
distortion,
etc.)
of
the
signal
currently being
received. Consequently,
optimum re-
ception
(the
lowest distortion and
highest S/N
ratio) is
assured
at
all times. Note that the
APR system
functions only during
FM reception. An
Auto Stereo/Mono
Selector,
lF
bandwidth
selector
and auto
hi-blend selector
are
provided
to allow
man-
ually overriding
these three
APR controlled
reception modes.
lf the station is
retuned, or the
APR button is
pressed
again
however, the or¡ginal
APR selected
modes will be
restored.
The APR system
functions automatically
when using the
UP
or
DOWN
.buttons,
or direct
tuning.
The APR settings are
memorized
when the station
is memorized.
I How
to name
preset
stat¡ons
(Character
memory function)
This function
enables
you
to
memorize a
maximum of 5
char-
acters
consisting of alphabetics, some
symbols and
numbers,
for
instance, representing broadcasting
station
names, for
each
preset
station.
.
DOWN
/UP
-
CLASS I\
ø@
DISPLAY
CHARACTER
The display shows an FM broadcast
at 105.11 MHz has been
memorized
in 1 CH
of
the CLASS A, and hat been named
"oNKYO".
@
Call
up
the stat¡on to be named, using the
CLASS A Button.
a
lf the bröadcast
has not
yet
been
memorized in the
preset
station, see Page 5.
@
Press the DISPLAY button.
a
The frequency
in the display
goes
off and the cursor
flashes at the first character.
n
1';
IIE
F
E
l-1
I
,-l
i-(
l-
l'l
l"l
Ü
t-t nt-t TTttt/tt\/t/-7
l-t
t_-l:_t
f-LlfiJ
ttt!/
l/\l
/\
t
/
U
ll:J
,l',a
E
-ii7
ri
,'
)K
-f
I tl /
\
!)
@
Select a
character using the UP
>
or DOWN
<
button
while thè cursor is
flashing
(approx.
5
seconds).
o
The
characrer
changes lrom
"
f-f
"
to
"
-_il
", "
|
"
ana
so on when
pressing
the UP
I
buttonland
changes in
reverse
order
when
pressing
the DOWN I
button.
@
Press
the
CHARACTER button once
more
when
the desired
character is displayed. The
character
will be memorized
and
the cursor moves to the next
character.
o
Select 5 characters
by repeating steps
@
and
@
. lf
you
want to include a space,
press
the
CHARACTER button.
@
Press the
CHARACTER button after selecting
5
characters.
ä,,iääirifräi"""'-1" llt',i t( \' tl..:". l? t""
o
Flashing stops, and the
naming operation
is
complete.
I
How to change the
character
Press the
CHARACTER
button
to flash the character and
select
the desired character using the
UP
>
and
DOWN
<
buttons.
I How to delete all characters
at once
Press the
DISPLAY button, while
holding down the CHAR-
ACTER button.
I
How
to
use the DISPLAY button
When characters
are memorized
for
a
preset
slation,
pressing
the CLASS Button does
not display the
frequency, but the
characters.
Press
the
DISPLAY button
if
you
wanï to display
the
frequency.
NOTE:
lf
you press
DISPLAY once,
and the
wrong characters appear,
press
the
button twice
more: once
to display the
frequency, then
once more to display the
correct character sequence.
o
Press
the
DISPLAY button once more
if the cursor stops
f lashing.
E
ÞE
I
I
To Next Page
Loading...
Need help?
General
