Onkyo TX-811 - Remote Control Connections (TX-822 only); Remote Control Operation; Canadian Models Operation; Direct Function Feature

Tape Deck and Graphic Equalizer Connections (EAEE: -1,
TAPE-2)
1.
This unit has facilities for two tape decks. If you are using only
one tape deck, connect it to the TAPE-1/VIDEO jacks. If you
have two tape decks, connect one to the TAPE-1/VIDEO jacks
and the other to the TAPE-2 jacks.
. Connect the output leads of the tape decks to the TAPE-1/VIDEO
and TAPE-2 “PLAY” jacks. Connect the input leads of the tape
decks to the TAPE-1/VIDEO and TAPE-2 “REC” jacks of the
unit. For more details, refer to your tape deck instruction manual.
. To connect a graphic equalizer, too, use the TAPE-2 jacks and
connect the second tape deck to the tape jacks of the equalizer.
(See the figure on the right.)
For the audio signal of a VDP, VCR, etc., make the connections
to the TAPE-1/VIDEO “PLAY”, “REC” jacks. For details, refer
to the operating instructions of the video equipment concerned.
. If you have an Onkyo tape deck with the fQI remote control
jack, connect it to the TAPE-1/VIDEO jacks. Please refer to the
section “Connections for Remote Control” on this page re-
garding connection of the remote control cable. (TX-822 only)
(TX-822 only)
Connections for Remote Control (REMOTE CONTROL)
A cassette tape deck and compact disc player that have the
Onkyo fi mark can be operated, using the accessory remote
control transmitter. ( (RE: Remote Interactive)
TX-822
FI REMOTE (Om
CONTROL
COMPACT
DISC PLAYER
FRI REMOTE
CONTROL
CASSETTE
TAPE DECK £
REMOTE
©
Dace
An §RE remote control cable equipped with a 0.136”
(3.5mm) diameter miniature two-conductor phone plug
is attached to the TX-822 and to any compact disc
player, with the f-3— mark.
To use an Onkyo compact disc player and cassette tape deck
with the f1 mark, insert the accessory remote contro! cable
plug into the REMOTE CONTROL jacks. As far as connecting
sequence is concerned, it doesn’t matter whether the cable is
connected from the TX-822 to the cassette tape deck or to the
compact disc player: The remote control transmitter is operated
by facing it towards the remote control sensor of the TX-822.
NOTE:
Remote control operation is not possible when only the remote
control cable is connected. Remote control cable and pin cord
must be connected.
Canadian models only
if you own a Canadian model of the TX-822, the Onkyo turntable
can be operated, using the accessory remote control transmitter.
® {ff your turntable has an fQ1_ mark on it, insert the accessory
fR1 remote control cable plug attached to the Onkyo
turntable with the FRE mark into the PHONO of the
TX-822's REMOTE CONTROL.
@ Onkyo turntables that can be remote controlled but do not
have the RI mark. This equipment has a 7-pin DIN jack
on the rear panel. Connect this jack and the jack on the rear
of the TX-822 with the special cable for this purpose, which
is sold separately.
To connect a graphic equalizer and second tape dec by
to the TAPE-2 jacks.
To TAPE-2 “REC” jacks of TX822/811
To-TAPE-2 “PLAY” jacks of TX-822/811 ~
Graphic equalizer
Second tape deck
TURNTABLE with the FR EP mark
TURNTABLE with no FRE mark
fo. & FRI REMOTE
202 | CONTROL %
i nemore RON cHone:
CONTROL RIE |
Ce TX-822
i remote KON prone
CONTROL RI
For this special cable.
Contact an Onkyo Service Center.
For a turntable
(3.5 mm pin to 7-pin plug cable)
part number; 2010140
TX-822
Direct function feature
NOTE:
This function works when an Onkyo cassette tape deck or
CD player with the FRI mark is connected to a TX-822 with
an fR1 remote control cable.
Just
by
directly
operating
the
desired
component
(compact
disc
player,
or
tape
deck),
the
TX-822’s
input
selector
automatically
switches
to
that
component.
The
component
that
was
being
used
stops,
and
the
desired
component
starts
operation.
Therefofe;
it
is
not
necessary
to
switch
the
TX-822’s
input
selector
when
changing
listening
sources.
Another
way
to.
switch
listening
sources
is
to
press
the
TX-822’s
input
selector
of
the
desired
listening
source.
The
current
listening
source
will
then
stop
au-
tomatically
and
the
desired
listening
source
will
start
operation.
Example 1
When the compact disé player's play button is pressed, the
TX-822’s
input
selector
will
switch
automatically
to
“CD.”
if
the
current
listening
source
was
a
tape
deck,
tape
playback
will
Stop
and the compact disc player will start playing.
Example 2
With
a
tape
deck
as
the
current
listening
source,
if
the
TX-822’s
input
selector
is
switched
to
“CD,”
the
tape
deck
will
stop
playing
and
the
compact
disc
player
will
start
playing.
NOTE:
@ The direct function fasnue dogs not apply to turntable.
@
|nsome
cases,
the
direct
function
may
not
work
the
f#tst
time
the
input
selector
is
pressed.
Pressing
the
input
selector
again
will
enable
the
direct
function.
(This
is
to
prevent
irregular
unit
operation.»