Oregon Scientific WMR112A - VIEWING OUTDOOR TEMPERATURE RECORDS; CLEARING OUTDOOR TEMPERATURE MEMORY; OUTDOOR AND CHANNEL HUMIDITY; SELECTING HUMIDITY SOURCES

5
GB
Note: The unit of all temperature related display will be changed
simultaneously.
To display the maximum and minimum temperatures,
1. Press the outdoor/channel temperature window.
2. Press [CHANNEL] for the outdoor thermo-hygrometer or the
desired channel.
3. Press [MEMORY] repeatedly for the desired record. The time and
date of the record will also be displayed alternatively with
“STAMP” icon in the clock window.
To display the dew point temperature for a channel, press the
window again when the channel temperature is located.
To clear the memory,
1. Press the outdoor/channel temperature window.
2. Press [CHANNEL] for the outdoor thermo-hygrometer or the
desired channel.
3. Press and hold [MEMORY] till a key tone is heard.
4. Press [MEMORY] to check if the memory is clear.
To display the dew point maximum and minimum temperatures,
1. Press the outdoor/channel temperature window repeately until
"DEW" icon appear.
2. Press [CHANNEL] for the outdoor thermo-hygrometer or the
desired channel.
3. Press [MEMORY] repeatedly for the desired record. The time and
date of the record will also be displayed alternatively with
“STAMP” icon in the clock window.
To display the dew point temperature for a channel, press the
window again when the channel temperature is located.
To clear the dew point memory,
1. Press the outdoor/channel temperature window repeatedly until
"DEW" icon appear.
2. Press [CHANNEL] for the outdoor thermo-hygrometer or the
desired channel.
3. Press and hold [MEMORY] till a key tone is heard.
4. Press [MEMORY] to check if the memory is clear.
OUTDOOR AND CHANNEL HUMIDITY
The relative humidity readings taken by the outdoor thermo-
hygrometer and separate thermo-hygro sensors are displayed on
the outdoor/channel humidity window.
As this window can display up to four different sets of data, specify
the instrument or channel you want to read.
To do so,
1. Press the outdoor/channel humidity window.
2. Press [CHANNEL] to go from the outdoor reading taken by the
thermo-hygrometer to those taken by individual sensors
(Channel 1, 2 or 3).
To display the maximum, minimum and current humidity,
1. Press the outdoor/channel humidity window.
2. Press [CHANNEL] for the outdoor thermo-hygrometer or the
desired channel.
3. Press [MEMORY] repeatedly for the desired record. The time and
date of the record will also be displayed alternatively with
“STAMP” icon in the clock window.
To clear the memory,
1. Press the outdoor/channel humidity window.
2. Press [CHANNEL] for the outdoor thermo-hygrometer or the
desired channel.
3. Press and hold [MEMORY] till a key tone is heard.
4. Press [MEMORY] to check if the memory is clear.
AUTO SCANNING FUNCTION
The auto scanning function is avalibable for the outdoor/channel
window for both the temperature and humidity.
To use it,
1. Press the outdoor/channel temperature or humidity window.
2. Press and hold [
] until another key tone is heard. The main
unit will start scanning from the active temperature and humidity
display. Each channel will be displayed for about 4 seconds.
To exit the auto scanning routine, press any window or control
button.
WEATHER ALARMS
Weather alarms are used to alert you to certain weather conditions.
Once activated, the alarm will go off when a certain set of criterion
is met.
You can set alarms for:
• Indoor, outdoor and channel high temperatures
• Indoor, outdoor and channel low temperatures
• Indoor, outdoor and channel dew point approaching
• Indoor, outdoor and channel high humidity
• Indoor, outdoor and channel low humidity
• High rainfall rate "This feature works only with the optional
item: Rain gauge (RGR968)"
• Pressure drop
• High gust wind "This feature works only with the optional
item: Anemometer (WGR968)"
• Low wind chill "This feature works only with the optional
item: Anemometer (WGR968)"
To set a weather alarm,
1. Press the window containing the weather element you want to
set.
2. Press [ALARM]. The current alarm setting will be displayed.
3. Press and hold [SET].
4. Press [
] and [ ] for the desired setting.
5. Press [SET].
For temperatures and humidity, the high and low alarms can be set
in sequence. After entering the value for one alarm, you will be
prompted to enter the value for the other.
A weather alarm is activated once set. When the set criteria are met,
an alarm will go off and the current reading will flash together with
the corresponding indicator.