What to do if the chain of my Oregon CS1500-091 is loosening or coming off of the guide bar?
If the chain on your Oregon Chainsaw keeps loosening or coming off the guide bar, it's likely that the side cover isn't installed correctly. Make sure to properly install the side cover, ensuring the tab at the rear is tucked into the saw body.
What to do if my Oregon CS1500-091 motor does not run or runs intermittently?
If your Oregon Chainsaw motor doesn't run or runs intermittently, here's what you can check: * Ensure the saw is properly plugged in. * Inspect the cord for damage; replace a damaged extension cord, but consult a service location if the chainsaw cord is damaged. * Reset the GFCI outlet if it has tripped. * Try a different electrical outlet. * Disengage the chain brake by setting the front hand guard to the operating position. * Press the trigger lock-out before squeezing the trigger switch. * Unplug the chainsaw and clean out any debris from the side cover.
Why does my Oregon CS1500-091 motor stop while cutting?
If your Oregon Chainsaw motor stops while cutting, it could be due to a few reasons: * The chain might be pinched in the cut. Try undercutting the limb to relieve pressure. * The cord could be damaged. Replace a damaged extension cord, but consult a service location if the chainsaw cord is damaged. * The chain brake might be engaged. Ensure the front hand guard is in the operating position.
What to do if my Oregon Chainsaw does not cut properly?
If your Oregon Chainsaw isn't cutting properly, consider these possibilities: * The chain might not be tensioned enough, so tension the chain. * The chain might be dull. * The chain might be installed backwards, so install the chain with the teeth facing the correct direction. * The chain might be worn, so replace it. * The chain might be dry or excessively stretched, so check and refill the oil reservoir if needed. * The chain might not be in the bar groove, so reseat chain onto groove.
What to do if the bar and chain of my Oregon CS1500-091 are excessively hot and/or smoking?
If the bar and chain on your Oregon Chainsaw are excessively hot and/or smoking, it's likely that the chain is under-lubricated. Check the oil level and refill the oil reservoir if necessary.
How to fix an Oregon CS1500-091 when the motor runs, but the saw chain does not rotate?
If the motor of your Oregon Chainsaw runs, but the saw chain doesn't rotate, it could be because: * The chain isn't engaging the drive sprocket. Reinstall the chain, making sure the drive links are fully seated on the drive sprocket. * The guide bar nose sprocket isn't turning. Replace the guide bar.
What to do if my Oregon CS1500-091 motor does not stop when the chain brake is engaged?
If your Oregon Chainsaw motor doesn't stop when the chain brake is engaged: * Clean any debris that may be preventing the full movement of the front hand guard. * WARNING: OPERATING A CHAIN SAW WITHOUT A FUNCTIONING CHAIN BRAKE COULD LEAD TO SERIOUS PERSONAL INJURY. Contact an approved service location before using.
Why is my Oregon Chainsaw not cutting properly?
If your Oregon Chainsaw isn't cutting properly, consider these potential causes: * The chain may lack sufficient tension; adjust the tension. * The chain might be dull; sharpen the chain. * The chain could be installed backward; ensure the teeth face the correct direction. * The chain might be worn; replace it if necessary. * The chain could be dry or excessively stretched; check and refill the oil level if needed. * The chain might not be in the bar groove; reseat the chain onto the groove.
What to do if the motor of my Oregon CS1500-091 runs, but the saw chain does not rotate?
If the motor of your Oregon Chainsaw runs but the saw chain remains stationary, examine these possibilities: * The chain might not be engaging the drive sprocket; reinstall the chain, ensuring the drive links are fully seated. * The guide bar nose sprocket may not be turning; in this case, replace the guide bar.
What to do if the motor of my Oregon CS1500-091 does not stop when the chain brake is engaged?
If the motor of your Oregon Chainsaw continues to run even when the chain brake is engaged: * Clean any debris from the external chain brake mechanism that may be preventing full movement of the front hand-guard. * Be aware that a possible chain brake malfunction could lead to serious personal injury.
General| Type | Cordless Chainsaw |
|---|---|
| Bar Length | 16 in |
| Battery Voltage | 40V |
| Weight | 13.2 lbs (with battery) |
| Chain Speed | Varies with load, up to 12.5 m/s |
| Power Source | Battery |
| Motor | Brushless |
| Chain Pitch | 3/8 inch |
| Chain Gauge | 0.050 inches |
To Next Page
