LED Desk Lamp with Color Changing Tunnel
CY4G59-FFP CY4009-FFP T5U
CONGRATULATIONS!
You’ve purchased the finest in natural lighting technology with
your new OttLite
®
product.
PRODUCT REGISTRATION FORM
Please complete the enclosed Product Registration Form and
return it today by mail, or register online by going to:
OttLite.com/warranty
NOTE: THIS UNIT IS FULLY ASSEMBLED
1. Remove lamp from packing placing lamp body base (A) flat on
a steady surface.
2. Connect the AC Adapter input (J) into connector (K) in the rear-
bottom of the lamp.
3. Plug the AC adapter (L) into a standard household 120V AC
outlet. Note: Only use with the supplied AC adapter to
avoid damage or fire.
4. Turn the lamp ON & OFF by using power switch (C) in lamp
control panel (B).
5. Lamp control panel (B) includes multiple “touch” keys that
control the lamp’s light color and brightness settings, as well
as a color changing tunnel. This lamp provides three color
modes and five levels of brightness. See Touch Key Panel
Instructions section for operating instructions.
6. To position the shade simply bend the flex-neck (O) as needed to
point the light. Please hold the lamp base (A) while adjusting the
lamp. Take care not to overextend the lamp to avoid unbalancing
it and damage. Please refer to diagrams for lamp maximum
adjustment range.
Touch Key Panel Instructions:
To operate LED color & brightness settings, slightly touch the
required “key” to achieve the following:
• Turn lamp “ON/OFF”: touch power key (C).
• To adjust lighting color mode: touch “M” key (D) to switch
light color temperature mode; 5000°K, 2700°K, 4000°K.
NOTE: 5000°K is default color mode.
• There are five preset brightness levels. To adjust brightness:
touch the up arrow (E) to increase brightness and the down
arrow (F) to lower brightness.
To operate LED Color Changing Tunnel:
• The Color Changing Tunnel can be turned ON & OFF by
touching the power switch (G) located to the left of the light
changing bar (H).
• Turn the light changing bar to “ON” status. To engage
function for different colors, do one of the following:
· Touch desired color represented within light changing bar (H);
· Slide finger along light changing bar (H) in either direction;
· Touch the light changing bar power switch (G) for “three
seconds” and watch light color change automatically.
SAFETY WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS
1. Turn lamp off and WAIT UNTIL LAMP HEAD (M) AND
ADAPTER (L) ARE COOL before handling.
2. The LED panel (N) might get hot after several hours of
continuous use, DO NOT place your hands directly on LED
light panel.
3. Never use with an extension cord unless the plug can be fully
inserted into the receptacles in the extension cord.
4. Do not alter the plug.
5. The lamp head included with this unit cannot be replaced by
the consumer.
NOTE: The important safety instructions appearing in this
instruction sheet are not meant to cover all possible conditions
and situations that may occur. It must be understood that
common sense, caution, and care must be used with any
electrical product.
CAUTION! IF THE ExTERNaL FLExIbLE CabLE OR CORD OF THIS LUmINaIRE
IS DamagED, IT SHaLL bE ExCLUSIvELY REPLaCED bY THE maNUFaCTURER OR ITS
SERvICE agENT OR a SImILaR qUaLIFIED PERSON IN ORDER TO avOID a HazaRD.
INDOOR USE ONLY.
FCC PART 15
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that the interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that of
the receiver.
• Consult the dealer or an experienced radio/TV technician for help.
CAN ICES-3 (B)/NMB-3 (B)
CAUTION: Any change or modification to product not
expressly recognized by OttLite Technologies voids OttLite’s
responsibility for proper function of product.
AC/DC ADAPTER
Input: AC 100-240V, 50/60 Hz, 0.8A
Output: 12V DC, 1.5A with a Male DC Plug
THIS LAMP CONTAINS a 5V-2.1A USB output port (P) located on
the base of the lamp. USB port can charge such items as tablets,
cellular phones, etc.
EnGlish LED Desk Lamp with Color Changing Tunnel
INS150221 REV010715
N
C
B
A
90°
30° 30°
45° 45°
K
J
L
P
M
O
M
D
G
H
E
F
To Next Page
Need help?
General
