Owon XDS3204AE - Page 42

To Next Page

To Previous Page

4.Advanced User Guidebook

Figure 4-2 Rectangle window

Figure 4-3 Blackman window

Main Page

Table of Contents4
General Safety Requirements8
Safety Terms and Symbols9
Junior User Guidebook11
Introduction to the Structure of the Oscilloscope12
Front Panel12
Front Panel Menu Buttons13
Rear Panel13
Control Area14
User Interface Introduction15
How to Implement the General Inspection17
How to Implement the Function Inspection18
How to Implement the Probe Compensation19
How to Set the Probe Attenuation Coefficient19
How to Use the Probe Safely20
How to Implement Self-Calibration21
Introduction to the Vertical System21
Introduction to the Horizontal System22
Introduction to the Trigger System23
Touchscreen Controls (Touchscreen Is Optional)24
Operate the Menu through Touchscreen24
Gestures in Normal Mode25
Gestures in Wave Zoom Mode28
Other Operations Using Touchscreen30
Magnifier Function (Only for XDS3102AP/XDS3202A with Touchscreen)31
Advanced User Guidebook33
How to Set the Vertical System34
Use Mathematical Manipulation Function36
Waveform Math38
User Defined Function38
Digital Filter39
Using FFT Function39
Use Vertical Position and Scale Knobs44
How to Set the Horizontal System45
Zoom the Waveform45
How to Set the Trigger/Decoding System46
Single Trigger47
Alternate Trigger (Trigger Mode: Edge)56
Logic Trigger57
Bus Trigger58
Bus Decoding (Optional)63
How to Operate the Function Menu68
How to Implement Sampling Setup68
How to Set the Display System70
How to Save and Recall a Waveform73
How to Record/Playback Waveforms80
How to Clone and Recall a Waveform84
How to Implement the Auxiliary System Function Setting88
How to Update Your Instrument Firmware92
How to Measure Automatically93
How to Measure with Cursors97
How to Use Autoscale100
How to Use Built-In Help102
How to Use Executive Buttons102
How to Print the Screen Image104
Use the Arbitrary Function Generator (Optional)105
Output Connection105
To Set Channels105
To Set Signals106
To Output Sine Signals106
To Set the Frequency106
To Set the Period107
To Set the Start Phase107
To Set the Amplitude107
To Set the Offset108
To Set the High Level108
To Set the Low Level108
To Output Square Signals108
To Output Ramp Signals108
To Set the Symmetry of Ramp108
To Output Pulse Signals108
To Set the Pulse Width of Pulse108
To Set the Duty Cycle of Pulse108
To Output Arbitrary Signals108
Create a New Waveform109
File Browse110
Built-In Waveform110
Frequency Response Analysis112
Use the Multimeter (Optional)114
Input Terminals114
DMM Menu114
DMM Information Window115
Making Multimeter Measurements116
Measuring AC or DC Current116
Measuring AC or DC Voltage116
Measuring Resistance117
Testing Diodes117
Testing for Continuity117
Measuring Capacitance117
Multimeter Features118
Data Hold Mode118
Making Relative Measurements118
Information Display118
Auto or Manual Range118
Multimeter Recorder118
Communication with PC121
Using USB Port121
Using LAN Port122
Connect Directly122
Connect through a Router123
Using Wi-Fi to Connect with PC (Optional)125
Connect with PC as Wi-Fi Access Point125
Connect with PC as Wi-Fi Station126
Communication with Android Device Via Wi-Fi (Optional)129
How to Connect129
Connect with APP as Wi-Fi Access Point129
Connect with APP as Wi-Fi Station131
User Interface133
Gestures Control135
Demonstration137
Example 1: Measurement a Simple Signal137
Example 2: Gain of a Amplifier in a Metering Circuit138
Example 3: Capturing a Single Signal139
Example 4: Analyze the Details of a Signal140
Example 5: Application of X-Y Function142
Example 6: Video Signal Trigger143
10. Troubleshooting145
11. Technical Specifications146
Oscilloscope146
Trigger150
Waveform Generator (Optional)152
Multimeter (Optional)153
General Technical Specifications154
12. Appendix155
Appendix A: Enclosure155
Appendix B: General Care and Cleaning155
Appendix C: Battery Using Guide156

Owon XDS3204AE - Page 42

Table of Contents

Other manuals for Owon XDS3204AE

Related product manuals