The C10 Air Filling Machine is a lightweight, portable, and easy-to-operate inflatable device designed for packaging. It boasts a compact appearance, weighing less than 6kg, making it a cost-effective choice for small factories, warehouses, and shops.
Function Description:
The primary function of the C10 Air Filling Machine is to inflate air cushion bags for packaging purposes. It allows for adjustments to temperature, air volume, and speed to accommodate different bag characteristics. The machine is designed to work with specific film types provided by the manufacturer to ensure optimal performance and seal quality.
Important Technical Specifications:
- Model: C10
- Dimensions (LWH): 400MM * 360MM * 280MM
- Package Dimensions (LWH): 480MM * 270MM * 360MM
- Net Weight: 5.2 KGS
- Gross Weight: 6.5 KGS
- Input Voltage: AC 110/220V
- Rated Frequency: 50HZ/60HZ
- Power: 240W
- Heat Seal Temperature: 160-220°C
- Speed: 12m/min MAX
- Air Volume: 280L/min MAX
- Power Connection: Y
- Anti-electric Shock Sort: I
- Noise Level: Below 95 decibels (users should confirm local regulations)
- Storage Temperature: Machine: 0-43°C; Film: 0-43°C
- Operating Temperature: Machine: 16-43°C; Film: 16-43°C
- Power Requirements for Normal Operation: Average current 2A, peak current 3.5A.
Usage Features:
The C10 features a simple operation interface with a control panel that includes buttons for "LESS," "PLUS," "START/STOP," "SPEED," "TEMP," and "WIND."
- Installation: The film shaft is installed in its designated position (screwdriver needed).
- Power Connection: Connect the power cable to turn on the machine.
- Film Loading: Install the film onto the film shaft, ensuring it passes through the feed rod and is pulled into the middle of the belt.
- Auto-Feed: Press the auto-feed button to advance the film out of the filling machine.
- Start Filling: Press the start button to begin air filling.
- Adjustments: Temperature, air volume, and speed can be adjusted according to the film type and desired bag characteristics. Different films may require different parameters, and adjustments should be made based on actual conditions.
- Grounding: Proper grounding is crucial to prevent electric shock.
- Authorized Personnel: Only authorized technicians or qualified maintenance personnel should open the machine cover for repairs.
- Moving Parts: Keep fingers, hair, jewelry, and clothes away from the sealing roller and other moving parts when the machine is operating to prevent entanglement or scalding from high temperatures.
- Film Usage: Only use inflatable bags as packing materials; do not use them as floats, pillows, or child toys. The weight of the film should not exceed 5KG.
- Static Electricity: The machine generates static electricity, and the film itself may have static electricity. Operators should avoid wearing or dragging bare feet to prevent discomfort from static shock.
- Environment: Do not use the machine in humid environments. The film works best within the specified temperature range; exceeding or falling below this range might cause the film to break.
- Running Without Material: Do not run the machine without material.
- Error Codes: The manual provides error codes (LLL for temperature sensor, H-1 for heating strip, H-2 for motor, H-3 for air producer, H-4 for temperature) and advises contacting an authorized distributor or technician if they appear.
- Wiring Board: Using a wiring board may increase static electricity, potentially causing operational problems and discomfort.
Maintenance Features:
The manual outlines a preventive maintenance schedule:
- Weekly Maintenance (Check & Clean):
- Open the belt cover, blow off dust and fragments.
- Check for any abnormal abrasion components.
- Monthly Maintenance (Contact):
- Arrange an on-site inspection.
- Contact the authorized distributor or technical service representative to check the machine.
Replacement Procedures:
- Blade Replacement:
- Loosen the 3 screws at the root of the air pipe (refer to Pic 3).
- Take out the air pipe.
- Turn the screw counterclockwise to remove the old blade.
- Place the new blade in the groove in the windpipe.
- Turn the screw clockwise to fasten the new blade.
- Reinstall the air pipe, twisting 3 screws clockwise.
- High Temperature Belt Replacement:
- Use a screwdriver to remove the belt cover.
- Push the heating strip towards the traction wheel to loosen the belt.
- Remove the old belt.
- Replace with a new belt.
- Reinstall the belt cover.
- High Temperature Adhesive Tape Replacement:
- Use a screwdriver to remove the belt cover.
- Push the heating strip towards the traction wheel to loosen the belt.
- Remove the belt.
- Use a screwdriver to loosen the screw and gasket in the middle of the heating strip.
- Remove the heating strip (note: springs may slip out).
- Tear off the old high-temperature adhesive tape and paste a new one.
- Install the heating strip, belt, and belt cover back to their original positions.
Components (Refer to Pic 1 - Product Info):
- Machine Casing
- Air Filling Tube
- Heat Block Shield
- Control Panel
- Thin Film Guide Bar
- Film Roll Holder
- Standing Leg
- Heat Block
- Roller Drive Unit
- Fixed Screw of Gas-filled Tube
The C10 Air Filling Machine is CE certified, ensuring it meets European safety standards.
Need help?
General
To Next Page