To Next PageTo Next PageWhy is my Panasonic CS-RE18JKE so noisy?
If your Panasonic Air Conditioner unit is noisy during operation, check if it has been installed at an incline and ensure that the front panel is properly closed.
What to do if my Panasonic Air Conditioner doesn't receive the signal from the remote control?
If the Panasonic Air Conditioner unit isn't receiving the signal from the remote control, ensure that the receiver is not obstructed. Certain fluorescent lights may interfere with the signal transmitter; please consult authorized dealer.
What to do if my Panasonic Air Conditioner shows F91 error?
If your Panasonic Air Conditioner displays error code F91, it could be due to several reasons: * A refrigerant shortage, possibly due to a refrigerant leak. You should check for leaks. * Poor compression performance of the compressor. In this case, inspect and replace the compressor if necessary. * A closed 2/3 way valve. Ensure this valve is properly open. * Faulty indoor intake air or indoor pipe temperature sensors. Consider testing or replacing these sensors.
What does error code H98 mean on a Panasonic CS-RE18JKE?
If your Panasonic Air Conditioner displays the error code H98, it could be due to: * A clogged air filter in the indoor unit. Clean or replace the air filter. * Dust accumulation on the indoor unit heat exchanger. Clean the heat exchanger. * An air short circuit. Fix any air short circuit issues. * A faulty indoor pipe temperature sensor. Test or replace the indoor pipe temperature sensor. * A faulty indoor unit PCB. Check the indoor unit PCB.
How to fix H11 error on Panasonic CS-RE18JKE Air Conditioner?
If your Panasonic Air Conditioner is showing the H11 error code, it indicates a signal transmission error or a PCB fault. Here’s what you should check: * Inspect the indoor and outdoor unit PCBs. * Verify the wiring between the indoor and outdoor units. * Inspect the connection wires between the indoor and outdoor units for any breaks. * Check the power supply waveform.
What does error code H27 mean on my Panasonic CS-RE18JKE Air Conditioner?
If your Panasonic Air Conditioner displays error code H27, it indicates a problem with a connector, sensor, or PCB. Here’s what you should check: * Check the connector connections. * Test or replace the outdoor air temperature sensor. * Check the PCB.
What does error code H23 mean on Panasonic Air Conditioner?
If your Panasonic Air Conditioner displays error code H23, it indicates a problem with a connector, sensor, or PCB. Here’s what you should check: * Check the connector connections. * Test or replace the indoor heat exchanger temperature sensor. * Check the PCB.
What does H15 error code mean on a Panasonic CS-RE18JKE?
If your Panasonic Air Conditioner displays error code H15, it indicates a problem with a connector, sensor, or PCB. Here’s what you should check: * Check the connector connections. * Test or replace the outdoor compressor temperature sensor. * Check the PCB.
What should I do if my Panasonic Air Conditioner displays error F96?
If your Panasonic Air Conditioner shows error code F96, it means the IPM is overheating. This can be caused by: * A short circuit of hot discharge air flow. Inspect and repair any short circuits in the discharge air flow. * A defective outdoor fan motor. Inspect and replace the outdoor fan motor if necessary. * Defective internal circuitry of the IPM. Replace the IPM. * A defective IPM temperature sensor. Test or replace the IPM temperature sensor.
What causes the F99 error on a Panasonic CS-RE18JKE Air Conditioner?
If your Panasonic Air Conditioner displays error code F99, it indicates a DC peak issue. This could be due to: * Compressor failure. Inspect and replace the compressor if necessary. * Defective power transistor(s). Check and replace defective power transistors. * A defective outdoor unit PCB. Replace the outdoor unit PCB.
Safety guidelines for power cords, outlets, and earthing.
Precautions for indoor unit installation, operation, and cleaning.
Precautions for outdoor unit installation and handling.
How to select the desired operating temperature for the unit.
Explains different operation modes like AUTO, HEAT, COOL, and DRY.
Troubleshooting steps for common issues before contacting support.
Procedure to retrieve error codes using the remote control.
Safety guidelines for power cords, outlets, and earthing.
Precautions for indoor unit installation, operation, and cleaning.
Precautions for outdoor unit installation and handling.
How to select the desired operating temperature for the unit.
Explains different operation modes like AUTO, HEAT, COOL, and DRY.
Troubleshooting steps for common issues before contacting support.
Procedure to retrieve error codes using the remote control.
General| Brand | Panasonic |
|---|---|
| Model | CS-RE18JKE |
| Category | Air Conditioner |
| Language | English |
