157
Connection network using AP mode (method 2)
(For Android 5.0 and above & iOS 11 and above only)
1
Check that the Wireless LAN LED is ON. Press the Wireless LAN button for 5 seconds
until “1” appears on the remote control.
Press
until “2” appears. Point the remote control to the air conditioner and press
SET
.
Join to connect to the “Panasonic-CS-wirelessAP” network.
2
Enter the password of the selected wireless router and continue.
If Wireless LAN LED is OFF during the connec on
setup, please enable again by pressing “Wireless
LAN” bu
. 1 pets ot gnideecorp erofeb ecno no
1. Press and hold “Wireless LAN” bu
on for 5
secs un
l easy se ng “1” is shown.
2. Press “up” or “down” bu
on un l Advance
se
ng “2” is shown.
3. Point remote control to air-condi
oner and
press “SET” bu
on once.
4. A
er step 1
~
3 have been done, tap“Next”.
Connection Guide
Step 1
Step 2
Step 3
Cancel
Next
SET
CANCEL
f W
L
D
p
p
y
i
f
n
p 1
1.
L
f
y
n
.
“up”
“
wn”
v
.
in
l
r
i
r
n
E
”
n
4.
v
Connection Gui
e
tep 1
tep 2
tep 3
ance
ext
SET
AN
EL
Enter the password of the
selected wireless router.
MAC address of target device
SSID:Router_SSID1
Cancel OK
d8-61-62-f8-e6-67
If Wireless LAN LED is OFF during the connec on
setup, please enable again by pressing “Wireless
LAN” bu
. 1 pets ot gnideecorp erofeb ecno no
1. Press and hold “Wireless LAN” bu
on for 5
secs un
l easy se ng “1” is shown.
2. Press “up” or “down” bu
on un l Advance
se
ng “2” is shown.
3. Point remote control to air-condi
oner and
press “SET” bu
on once.
4. A
er step 1
~
3 have been done, tap“Next”.
Connection Guide
Step 1
Step 2
Step 3
Cancel
Next
SET
CANCEL
If Wireless LAN LED is OFF during the connec on
setup, please enable again by pressing “Wireless
LAN” bu
. 1 pets ot gnideecorp erofeb ecno no
1. Press and hold “Wireless LAN” bu
on for 5
secs un
l easy se ng “1” is shown.
2. Press “up” or “down” bu
on un l Advance
se
ng “2” is shown.
3. Point remote control to air-condi
oner and
press “SET” bu
on once.
4. A
er step 1
~
3 have been done, tap“Next”.
Connection Guide
Step 1
Step 2
Step 3
Cancel
Next
SET
CANCEL
If
L
D
t
n
n
y
L
f
1
.
n
r
L
f
y
1
w
.
s “up”
“
wn”
v
.
n
E
4.
p
”
Connection Gui
e
tep 1
tep 2
tep 3
Cancel
ext
SET
AN
EL
Allow “Comfort Cloud”
If Wireless LAN LED is OFF during the connec on
setup, please enable again by pressing “Wireless
LAN” bu
. 1 pets ot gnideecorp erofeb ecno no
1. Press and hold “Wireless LAN” bu
on for 5
secs un
l easy se ng “1” is shown.
2. Press “up” or “down” bu
on un l Advance
se
ng “2” is shown.
3. Point remote control to air-condi
oner and
press “SET” bu
on once.
4. A
er step 1
~
3 have been done, tap“Next”.
Connection Guide
Step 1
Step 2
Step 3
Cancel
Next
SET
CANCEL
f
L
ED
FF
i
p
in
pr
L
f
1
.
f
y
.
“up”
“
wn”
.
n
l
i
n
E
4.
r
n
n
p“
Connection Gui
e
tep 1
tep 2
tep 3
Cancel
ext
SET
AN
EL
“Comfort Cloud” Wants
to Join Wi-Fi Network
“Panasonic-CS-
wirelessAP”?
Cancel Join