To Next PageTo Next PageWhy is the TIMER indicator always on on my Panasonic CU-2Z41TBE Air Conditioner?
If the TIMER indicator on your Panasonic Air Conditioner is always on, it means the timer setting repeats daily once set.
Why does the indoor fan stop during automatic fan speed on my Panasonic CU-2Z41TBE Air Conditioner?
The indoor fan of your Panasonic Air Conditioner may stop occasionally during automatic fan speed setting to help remove surrounding odors.
What to do if Panasonic Air Conditioner doesn't receive signal from remote control?
If your Panasonic Air Conditioner isn't receiving the signal from the remote control: * Ensure that the receiver is not obstructed. * Be aware that certain fluorescent lights may interfere with the signal transmitter.
Why does Panasonic CU-2Z41TBE Wireless LAN LED stay ON during unit turn OFF?
If the Wireless LAN LED stays ON during unit turn OFF of your Panasonic Air Conditioner, it means the unit’s LAN connection with the router is activated.
Why does my room have a peculiar odor when using Panasonic CU-2Z41TBE Air Conditioner?
A peculiar odor in the room with your Panasonic Air Conditioner may be due to a damp smell emitted by the wall, carpet, furniture, or clothing.
What does it mean when Panasonic CU-2Z41TBE Air Conditioner POWER indicator blinks during HEAT mode?
If the POWER indicator on your Panasonic Air Conditioner blinks during HEAT mode with no warm air supply and the flap is closed, the unit is in defrost mode, and AIR SWING is set to AUTO.
Why does mist emerge from my Panasonic CU-2Z41TBE?
If you see mist emerging from the indoor unit of your Panasonic Air Conditioner, it is a condensation effect due to the cooling process.
Why does the POWER indicator blink on my Panasonic Air Conditioner before it turns on?
The POWER indicator on your Panasonic Air Conditioner might blink before the unit is switched on as a preliminary step in preparation for operation when the ON timer has been set. When the ON Timer is set, the unit may start earlier (up to 35 minutes) before the actual set time in order to achieve the desired temperature on time.
Why POWER indicator blinks during HEAT mode on Panasonic Air Conditioner?
If the POWER indicator on your Panasonic Air Conditioner blinks during HEAT mode and there's no warm air, with the flap closed, it means the unit is in defrost mode and AIR SWING is set to AUTO.
What to do if Panasonic CU-2Z41TBE unit does not work?
If your Panasonic Air Conditioner unit isn't working, check if the circuit breaker has tripped. Also, verify whether any timers have been set.
General| Cooling Capacity | 4.1 kW |
|---|---|
| Power Supply | 220-240 V, 50 Hz |
| Refrigerant | R32 |
| Operating Range Cooling | -10°C to 46°C |
| Operating Range Heating | -15°C to 24°C |
Read instructions thoroughly for future reference. Keep Installation Instructions for installer.
WARNING for death/serious injury, CAUTION for injury/property damage. Understand safety symbols.
Appliance use by children requires supervision. Do not install in flammable atmosphere.
Use correct cords, do not share outlets, avoid wet hands, do not bend cord. Ground equipment.
Appliance uses R32 (flammable refrigerant). Risk of fire if leaked near ignition source.
Install in minimum room area. Keep away from ignition sources. Ensure ventilation is clear.
Higher pressure than R22/R410A. Replace piping/flare nuts. Do not mix refrigerants.
Locate circuit/piping away from heat sources. Regularly check alarms and ventilation.
Requires knowledge of flammable refrigerants, handling skills, and relevant legislation.
Protect pipe-work from damage. Comply with gas regulations. Ensure accessible connections.
System inspected by trained personnel. Ensure refrigerant charge and no leaks. Work with controlled procedures.
Minimize flammable gas risk. Avoid confined spaces. Wear protective equipment. Keep ignition sources away.
Check area with detector. Use suitable equipment. Ventilate if leakage occurs.
No ignition sources during work. Do not smoke. Survey area for hazards before work.
Check electrical components, refrigerant charge, ventilation. Ensure markings are legible.
Disconnect power for repairs. Use leak detection. Check cabling for wear and environmental effects.
Use appropriate leak detection methods. Avoid naked flames for detection.
Recover refrigerant, purge with inert gas, evacuate. Use OFN for purging.
Prevent contamination, use short hoses, earth system, label system. Avoid overfilling.
Familiarize with equipment, isolate electrically, ensure handling equipment, PPE, supervision.
Recover refrigerant safely using appropriate cylinders. Ensure correct number of cylinders.
Use remote to retrieve error codes. Write down code and consult dealer.
Table of diagnostic codes (Hxx, Fxx) and their corresponding abnormalities/protections.
