To Next PageTo Next PageWhy does my Panasonic Air Conditioner show H11 error?
The error H11 in your Panasonic Air Conditioner indicates an abnormal communication between the indoor and outdoor units. This could be due to a faulty indoor or outdoor unit PCB, wrong wiring, a break in the connection wires, or a disturbed power supply waveform.
What does error H19 mean on my Panasonic CU-E24NKUA?
The H19 error in your Panasonic Air Conditioner indicates that the indoor fan motor is DC motor mechanism locked. This can be caused by a short circuit inside the fan motor winding, a break in the wire inside the fan motor, broken fan motor lead wires, Hall IC malfunction, or a faulty indoor unit PCB.
What does error F90 mean on my Panasonic CU-E24NKUA Air Conditioner?
The F90 error on your Panasonic Air Conditioner indicates power factor correction protection. It can be caused by a DC voltage peak due to a power supply surge, non-uniform compressor windings, or a faulty outdoor PCB.
What does F99 error mean on a Panasonic CU-E24NKUA?
The F99 error in your Panasonic Air Conditioner indicates an output over current detection. This can be caused by a DC peak due to compressor failure, defective power transistor(s), or a defective outdoor unit PCB.
What does H98 error mean on my Panasonic Air Conditioner?
The H98 error in your Panasonic Air Conditioner indicates indoor high pressure protection. This can be caused by a clogged air filter, dust accumulation on the indoor unit heat exchanger, an air short circuit, a faulty indoor pipe temperature sensor, or a faulty indoor unit PCB.
What does F95 error mean on a Panasonic CU-E24NKUA Air Conditioner?
The F95 error in your Panasonic Air Conditioner indicates a cooling high pressure abnormality. This could be due to a rise in outdoor pipe temperature caused by a short circuit of hot discharge air flow, a defective outdoor fan motor, a defective outdoor pipe temperature sensor, or a defective outdoor unit PCB.
What does H99 error mean on my Panasonic CU-E24NKUA Air Conditioner?
The H99 error in your Panasonic Air Conditioner indicates indoor freeze prevention protection during cooling or soft dry modes. This can be due to a clogged air filter, dust accumulation on the indoor unit heat exchanger, an air short circuit, a faulty indoor pipe temperature sensor, or a faulty indoor unit PCB.
What causes the F98 error on a Panasonic CU-E24NKUA Air Conditioner?
The F98 error in your Panasonic Air Conditioner indicates an input over current detection. This can be caused by compressor failure, a defective outdoor unit PCB, a defective inverter main circuit electrolytic capacitor, or excessive refrigerant.
Why is my Panasonic Air Conditioner showing F97 (Compressor Overheating)?
The F97 error on your Panasonic Air Conditioner indicates compressor overheating, which may be due to refrigerant shortage (refrigerant leakage), a closed 2/3 way valve, or a faulty compressor tank temperature sensor.
General| Cooling Capacity | 24000 BTU/h |
|---|---|
| Compressor Type | Inverter |
| Refrigerant | R32 |
| Type | Split System |
| Seasonal Energy Efficiency Ratio (SEER) | 16.0 |
| Power Supply | 220-240V/50Hz |
| Weight (Indoor Unit) | 9 kg |
Explains warning symbols and general safety precautions to prevent injury.
Specifies the recommended operating temperature ranges for cooling and heating.
Details power supply requirements and recommended circuit breakers.
Safety precautions related to children and batteries for the remote control.
Detailed safety measures for power cords and electrical shock prevention.
How to turn on/off, set temperature, and select operation modes.
Guides on adjusting fan speed and controlling airflow direction.
How to activate quiet mode to reduce operational noise.
Operations for quick temperature adjustment and indicator brightness.
Instructions for setting and cancelling ON/OFF timers.
Steps for cleaning the indoor unit and its parts.
Guidelines for cleaning and replacing air filters.
Lists common occurrences that are not actual malfunctions.
Essential checks to perform before contacting a dealer.
Procedure to retrieve and interpret error codes.
Guidelines for non-use and conditions requiring professional service.
Information on disposal and regulatory compliance statements.
Step-by-step instructions for setting up the remote control.
Quick guide to selecting mode, starting/stopping, and setting temperature.
