To Next PageTo Next PageWhat does H30 error mean on my Panasonic CU-S12NKUA?
The H30 error on your Panasonic Air Conditioner indicates an abnormality with the compressor discharge temperature sensor. This can be caused by: * A faulty connector connection, so check and secure connector connections. * A faulty sensor, so replace the compressor discharge temperature sensor. * A faulty PCB, so replace the defective PCB.
What does F91 error mean on my Panasonic Air Conditioner and how to fix it?
The F91 error on your Panasonic Air Conditioner signals a refrigeration cycle abnormality. This can be caused by: * A refrigerant shortage due to leaks, in which case you should check for leaks and recharge the system. * Poor compressor performance, so inspect the compressor. * A closed 2/3 way valve, so ensure the valve is open. * Faulty indoor intake air or pipe temperature sensors, so test and replace any faulty sensors.
How to troubleshoot H98 error related to high pressure in my Panasonic CU-S12NKUA Air Conditioner?
The H98 error indicates indoor high pressure protection. This may be due to: * A clogged air filter, so clean or replace it. * Dust accumulation on the heat exchanger, so clean it. * An air short circuit, so check for and eliminate it. * A faulty indoor pipe temperature sensor, so replace it. * A defective indoor unit PCB, so replace it.
Why does my Panasonic Air Conditioner show F98 error and how to fix it?
The F98 error on your Panasonic Air Conditioner indicates an input over current detection. This can occur due to: * Compressor failure, so inspect and replace the compressor if necessary. * A defective outdoor unit PCB, so replace it. * A defective inverter main circuit electrolytic capacitor, so replace it. * Excessive refrigerant, so check for proper refrigerant levels.
How to fix H19 error, when indoor fan motor is locked, in Panasonic Air Conditioner?
The H19 error on your Panasonic Air Conditioner indicates that the indoor fan motor mechanism is locked. This could be due to: * A short circuit inside the fan motor winding, so replace the indoor fan motor. * A broken wire inside the fan motor, so inspect and repair any broken wires. * Broken fan motor lead wires, so inspect and repair them. * Hall IC malfunction, so replace the Hall IC. * A faulty indoor unit PCB, so replace it.
What does F11 error mean on my Panasonic CU-S12NKUA Air Conditioner?
The F11 error on your Panasonic Air Conditioner indicates an abnormality with the indoor pipe temperature sensor. This can be caused by: * A faulty connector connection, so check and secure connector connections. * A faulty indoor pipe temperature sensor, so replace the indoor pipe temperature sensor. * A faulty indoor main PCB, so replace the faulty indoor main PCB.
How to troubleshoot H15 error (compressor temperature sensor abnormality) in Panasonic CU-S12NKUA?
The H15 error on your Panasonic Air Conditioner indicates an abnormality with the compressor temperature sensor. This can be caused by: * A faulty connector connection, so check and secure connector connections. * A faulty sensor, so replace the outdoor compressor temperature sensor. * A faulty PCB, so replace the defective PCB.
What does H23 error mean on my Panasonic CU-S12NKUA Air Conditioner?
The H23 error on your Panasonic Air Conditioner indicates an abnormality with the indoor pipe temperature sensor. This can be caused by: * A faulty connector connection, so check and secure connector connections. * A faulty sensor, so replace the indoor pipe temperature sensor. * A faulty PCB, so replace the defective PCB.
What does H16 error mean on Panasonic CU-S12NKUA?
The H16 error on your Panasonic Air Conditioner indicates an open circuit in the outdoor current transformer. This could be due to: * A defective current transformer, so replace it. * A defective outdoor PCB, so replace it. * A defective compressor (low compression), so inspect and replace the compressor if necessary.
What to do if Panasonic CU-S12NKUA Air Conditioner shows H12 error (capacity rank mismatch)?
The H12 error on your Panasonic Air Conditioner indicates a capacity rank mismatch between the indoor and outdoor units. This can be caused by: * Wrong models interconnected, so ensure compatible units are connected. * Wrong indoor or outdoor unit PCBs mounted, so check and replace incorrect PCBs. * Defective indoor or outdoor unit PCBs, so test and replace them. * Incorrect wiring between the units, so verify the wiring. * Broken wires in the connection wires, so inspect and repair any broken wires.
General| Refrigerant | R410A |
|---|---|
| Weight (Indoor Unit) | 9 kg |
| Indoor Unit Weight | 9 kg |
| Weight (Outdoor Unit) | 32 kg |
| Outdoor Unit Weight | 32 kg |
| Cooling Capacity | 12000 BTU/h |
