Panasonic DMC-FZ300PP - General Disassembly Procedures

28
9.3. Disassembly Procedure
No. Item Fig. Removal
1 Rear Case Unit (Fig. D1) Memory Card
Battery
Screw (A)  3
Screw (B)  3
Screw (C)  3
(Fig. D2) Locking tab (A)  2
Locking tab (B)  2
Locking tab (C)  2
Locking tab (D)  2
Eye Cap Unit
Screw (D)  2
(Fig. D3) When Installing
(Fig. D4) Locking tab  3
Rear Grip
Screw (E)  2
(Fig. D5) FP9003 (Flex)
FP9007 (Flex)
Rear Case Unit
2 Main P.C.B. (Fig. D6) Screw (F)  4
FP9001 (Flex)
FP9002 (Flex)
FP9004 (Flex)
FP9005 (Flex)
FP9006 (Flex)
FP9009 (Flex)
PS9001 (Connector)
Main P.C.B.
(Fig. D7) When Replacing
3 Top Case Unit
Battery Case Unit
(Fig. D8) Screw (G)  1
Locking tab  2
Battery Plate (with Thermal
Sheet C)
(Fig. D9) Screw (H)  1
Screw (I)  1
Screw (J)  1
Front Grip
(Fig. D10) Screw (K)  4
Screw (L)  2
Top Case Unit
Battery Case Unit
(Fig. D11) When Installong
(Fig. D12)
4 Lens Unit (Fig. D13) Screw (M)  4
Lens Unit
5 Mic Jack Holder,
Mic Jack P.C.B.,
Speaker
(Fig. D14) Screw (N)  1
FP9302 (Flex)
Convex  1
Mic Jack Holder
Mic Jack P.C.B.
Solder (2 points)
Speaker
6 Side Operation Unit
Front Case Unit
(Fig. D15) Screw (O)  2
Locking tab  2
Side Frame
Screw (P)  2
Lens Ring
Convex  4
Side Operation Unit
Front Case Unit
7 Battery Door Unit (Fig. D16) Screw (Q)  2
Battery Door Unit
8 Flash P.C.B. Unit (Fig. D17) Convex  1
Locking tab  1
(Fig. D18) Screw (R)  1
Locking tab (A)  3
Condenser Cover
Locking tab (B)  2
(Fig. D19) Solder (4 points)
Flash P.C.B. Unit
9 LVF Module (Fig. D20) Convex (A)  2
Hooking part (A)  2
Multi FPC Unit
Screw (S)  2
Convex (B)  2
Locking tab  2
Hooking part (B)  2
LVF Cover Unit
LVF Unit
Heat Radiation Pad
LVF Module
10 Flash Tray Unit,
Shoe Spring,
Flash Case Top
(Fig. D21) Screw (T)  3
Flash Tray Unit
Shoe Spring
Screw (U)  2
Locking tab  2
Flash Case Top
11 Rear Operation Unit
Hinge SW FPC
(Fig. D22) Screw (V)  2
Locking tab  1
Hinge Arm Cover
Screw (W)  12
Convex (A)  6
Rear Plate Unit
Convex (B)  5
Rear Operation Unit
Solder (6 points)
Convex (C)  8
Hinge SW FPC
12 LCD Hinge Unit
(with LCD Unit)
(Fig. D23) Convex  4
Screw (X)  2
Hinge Earth
Spacer
Hinge Fix Cover
Hinge Cushion 4
LCD Hinge Unit (with LCD
Unit)
13 LCD IF P.C.B.,
MR Sensor FPC,
LCD Unit
(Fig. D24) Screw (Y)  2
Screw (Z)  2
Locking tab  8
LCD Case Bottom
(Fig. D25) FP4101 (Flex)
FP4102 (Flex)
FP4103 (Flex)
FP4104 (Flex)
Locking tab  1
LCD IF P.C.B.
(Fig. D26) Convex  2
MR Sensor FPC
(Fig. D27) LCD Bezel Sheet
LCD Bezel
LCD Earth Plate  2
LCD Unit
(Fig. D28) When Installing
No. Item Fig. Removal