This unit does not recognize the
USB
connection
correctly.
:::;;...
If USB device is connected to this unit while playing a
disc or
in
a video communication the connection
will not
be recognized.
Press [HOME] and reconnect USB
device.
:::;;...
I BDT310 ii BDT21S
II
BDT210 I:
USB memory and USB
HOD
are not recognized via the rear
USB
port of this unit.
:::;;...
Disconnect and reconnect the
USB
cable.
If it still does
not recognize the connection, turn the power
of
this unit
off and on agai
n.
:::;;...
USB devices connected using a USB extension cable
other than the supplied with the Wireless LAN Adaptor
DY-WL 10
(optional)
I
BDT110!
or
a USB hub may not
be
recognized by this unit.
:::;;...
If
you connect USB HOD
to this unit, use USB extension
cable that is supplied with the
HOD.
:::;;...
If
two USB memory and USB
HOD
are connected
simultaneously, they will
not be recognized by this unit.
I
Picture
The images from this unit do not appear
on
the
television.
Picture
is
distorted.
:::;;...
An incorrect resolution
is
selected in
"HOM I
Resolution".
Reset the setting
as
follows:
CD
While the unit is
on
, press and hold [OK),
[B) and [Y]
on
the remote control at the same time for more than
5 seconds.
-
"00 RET"
is displayed on the unit's display.
®
Repeatedly press
[~)
(right) on the remote control
or
[POWER
<!.>II)
on the unit until
"04 PRG"
is displayed
on
the unit's display.
@
Press
and hold
[OK]
on
the remote control or
[~
OPEN/
CLOSE]
on the unit for at least 3 seconds.
Set the item
again
.
(~
31)
-When
Dolby Digital
Plus,
Dolby TrueHD, and DTS-HD
audio are not output in bitstream, select "Yes"
in
"Restore
Default Settings" and make proper settings.
(~
33)
:::;;...
When
"30
BD-Video
Playback" in the Setup menu is set
to
"Automatic
",
images may not
be
output depending on
the connection method. After removing the disc from this
unit, select
"Set before
play"
in the Setup menu, and
select
"20
Playback"
in
the setup screen displayed
when playing
30
discs.
(
~
29)
Video
is
not output.
:::;;...
I BDT310 II BDT21S II
BDT210
I :
Set "High Clarity
Sound"
in
the
Playback menu to
"
Off
'
to use the
VIDEO OUT
terminal.
(~
28)
:::;;...
I BDT310I :
Video from the
HDMI
AV
OUT
SUB terminal
is
not output when the
"HDMI(SUB) Output Mode"
is set
to
"V.OFF".
(~
31)
Video
is
not output
in
high-definition.
:::;;...
Confirm that "HOM I Resolution"
in
the Setup menu is set
properly.
(
~
31)
3D
video is not output.
:::;;...
Is
there a non-3D compatible amplifier/receiver
connected between this unit and a
TV?(~
9)
:::;;...
I
BDT310
I
:
If
there is a non-3D compatible amplifier/
receiver connected to the
HOM
I
AV
OUT
SUB terminal,
set the
"HDMI(SUB) Output Mode" to
"V.OFF".
(~
9)
:::;;...
Are the settings on this unit and the TV correct?
(
~
20)
:::;;...
Is
the amplifier/receiver that is connected between this
unit and TV on?
30
video is not output
correctly
as
20.
:::;;...
Select "
Set
before
play"
in
the Setup menu, and
se
lect
"
20
Playback"
in the setup screen displayed when
playing
30
discs.
(~
29)
:::;;...
Discs that have recorded titles with Side by side
(2 screen structure) and that can be enjoyed
in
30
are
played back
in
accordance with the settings
of
the
TV.
No
subtitles.
:::;;...
When progressive output is on, closed captions/subtitles
cannot be displayed.
The subtitles overlap closed
captions
recorded on discs.
:::;;...
Turn off the subtitles
or
turn off the closed caption
setting on the
TV.
(~
27)
A
black
band
is
displayed
around the edge
of the screen.
The aspect ratio
of
the screen
is
abnormal.
:::;;...
Confirm the "TV Aspect"
is
set properly.
(~
31)
:::;;...
Adjust the aspect setting on the television.
I
Audio
Cannot switch audio.
:::;;...
When connecting an amplifier/receiver using an
OPTICAL
terminal
or
an
HOM I terminal, you cannot
switch
th
e audio
if
"Digit
al
Audio
Output"
is set to
"Bitstream
".
Set
"Digital Audio
Output"
to "PCM
".
(9
30)
Cannot hear the desired audio type.
:::;;...
Check the connections and the
"Digital
Audio
Output"
settings.(~
9,
30)
:::;;...
To
output audio from a device connected with
an
HOM
I
cable, set
"HOM I
Audio
Output"
to
"On"
in the Setup
m
e
nu
.
(
~
32)
:::;;...
I BDT310
I
:
When connecting this unit to a
TV
via an
HOM I
AV
OUT MAIN
and to
an amplifier/receiver
via
an
HOM I
AV
OUT SUB, set
"HDMI(SUB) Output Mode" to
"V.OFF".
(
~
9)
There is no sound coming out from the
TV.
IBDT310I
:::;;...
Audio may not output from the TV
wh
en the amplif
ie
r/
receiver is connected to the
HOM I
AV
OUT
SUB,
and
"HDMI(SUB) Output
Mode
"
(
~
31) is set to ''V.OFF
".
In
such a case, output audio from the amplifier/receiver.
To
output audio from the TV, set the
"HDMI(SUB) Output
Mode"
to "Normal
".
VQT3B58
35
To Next Page
Loading...
