Messages
The
following messages or service numbers appear on the
television
or
unit's
display
when something
unusual is
detected during startup and use.
I On
the television
Cannot
play.
>-
You
inserted an
incompatible
disc (Discs recorded
in
PAL
video, etc.).
Cannot
display
on
this
unit.
>-
You
tried to play
a non-compatible image.
>-
Confirm "SO"
on the unit's
display
is not
displayed and
re-insert the card.
No
disc
is
inserted.
>-
The disc may
be
upside down.
0
This
operation
is
not
available.
>-
Some
operations are unsupported by the unit. For
example;
- BD-Video: During playback,
reverse
slow-motion
or
reverse frame-by-frame is not
possible.
IP
address
is
not
set.
>-
The
"IP Address" in
"IP
Address/DNS
Settings"
is"---
.
---. ---.
---". Set
the "IP Address",
"Subnet Mask",
and
"Default
Gateway". (Select the automatic address
acquisition
if
necessary.)
The
current
settings
only
offer
minimal
wireless
access
point
security
and
low
performance.
It
is
recommended
to
change
it
for
better security.
>-
Authentication type for the
Wireless
LAN is set to "Open
system", or the encryption type is set to
"No
encryption".
It
is recommended to encrypt for safety reasons. For
details,
refer to the instructions of the
Wireless
router
being used. Encryption is required when
playing
back
video, etc., from DLNA compatible devices.
I On
the unit's display
F99
>-
The unit
fails
to operate
properly. Press [POWER
<!>II]
on the main unit for 3 seconds to switch the unit to
standby, then switch back on.
HDMI ONLY
>-
Some
BD-Video discs can
only
be output with
HOM
I.
NET
>-
While
connecting to a network.
No PLAY
>-
There is a viewing restriction on a BD-Video
or
DVD-Video.
(Q
29)
No
READ
>-
The media
is
dirty
or
badly scratched. The unit cannot
play.
PLEASE WAIT
>-
The unit is carrying out
an
internal
process. This is not a
malfunction.
You
cannot operate the unit while "PLEASE
WAIT"
is
displayed.
REMOVE
>-
The
USB
device is drawing too much power. Remove
the
USB
device.
SETD
("
D
"
stands
for
a number.)
>-
The remote control
and main unit are using different
codes. Change the code on the remote
control.
Press and
hold [OK]
and the
indicated number button at the
same time for more than
5 seconds.
U59
>-
The unit is hot.
rrr
(21
--
r
'
_,_
The unit switches to standby for safety reasons. Wait for
about
30
minutes until
the message disappears.
Select
a position with good
ventilation
when installing
the unit. Do not block
the
ventilation hole
on the si
de
of
the unit.
HDDorFDD
("
D
"
stands
for
a number.)
>-
There
is
something
unusual.
>-
Check the unit using the troubleshooting guide.
If
the
service number does not disappear,
do
the following.
CD
Disconnect the
plug
from the
AC outlet, wait a few
seconds, then reconnect it.
®
Press [POWER
<9/1]
to turn the
power
on.
If the service number does not disappear despite doing the
above, request service from the
dealer. Inform
the
dealer
of
the service number when requesting service.
START
>-
The system is being restarted during the firmware
update.
Please do not turn
off
the unit.
UPDD/D
("
D
"
stands
for
a number.)
>-
The firmware is being updated.
Please
do not turn off the unit.
FINISH
>-
The firmware update is
complete.
VQT3858
37
To Next Page
Loading...
