31
Useful Information
4 <Only for model with TPM> Clear TPM.
A
Perform either of the following procedures.
y
Touch and hold
at the bottom left corner of the Desktop screen.
y
Flick from the middle of the Start screen to the top.
B
7RXFK>5XQ@DQGLQSXW>WSPPVF@DQGWRXFK>2.@
C
7RXFK>&OHDU730«@XQGHU³$FWLRQV´RQWKHULJKWRIWKH³7300DQDJHURQ/RFDO&RP
puter” screen.
D
7RXFK>5HVWDUW@RIWKH³0DQDJHWKH730VHFXULW\KDUGZDUH´VFUHHQ
The computer will restart.
E
:KHQ³730FRQ¿JXUDWLRQFKDQJHZDVUHTXHVWHGWR´LVGLVSOD\HGSUHVV
F12
.
F
7RXFKWKH'HVNWRSWLOHDQGZKHQ³730LVUHDG\´DSSHDUVWRXFK>&ORVH@
Hard disk (Flash memory) recovery
Preparation
z
Remove all peripherals.
z
Connect the AC adaptor and do not remove it until installation is complete.
You can reinstall the OS that was pre-installed at the time of purchase (Windows 8.1 or Windows 7).
If reinstallation using the method described in “Remove everything and reinstall
Windows” above is not successful, follow the steps below.
1 Start the Setup Utility.
A
Display “Charm”, and touch
>&KDQJH3&VHWWLQJV@>8SGDWHDQGUHFRYHU\@>5HFRY
HU\@
B
7RXFK>5HVWDUWQRZ@XQGHU³$GYDQFHGVWDUWXS´
C
7RXFK>7URXEOHVKRRW@>$GYDQFHGRSWLRQV@>8(),)LUPZDUH6HWWLQJV@>5HVWDUW@
7XUQRQWKHFRPSXWHUDQGWRXFKWRSOHIWRIWKHVFUHHQZKLOH>3DQDVRQLF@ERRWVFUHHQLV
displayed.
z
,IWKH>3DQDVRQLF@ERRWVFUHHQLVQRWGLVSOD\HGWXUQRQWKHFRPSXWHUZKLOHWouching top
left of the screen.
z
If the password is requested, enter the Supervisor Password.
2 Write down all of the contents of the Setup Utility and touch [Exit] and
double-touch [Load Default Values].
$WWKHFRQ¿UPDWLRQPHVVDJHWRXFK><HV@
3 Check the [UEFI Boot] setting of the Setup Utility.
>8(),%RRW@VKRXOGEHVHWWRDVIROORZV
:KHQLQVWDOOLQJ:LQGRZV>(QDEOHG@
:KHQLQVWDOOLQJ:LQGRZV >'LVDEOHG@
4 Touch [Exit] and double-touch [Save Values and Reboot].
$WWKHFRQ¿UPDWLRQPHVVDJHWRXFK><HV@
Computer will restart.
5 Touch top left of the screen while [Panasonic] boot screen is dis-
played.
The Setup Utility starts up.
z
If the password is requested, enter the Supervisor Password.
6 Touch [Exit] and double-touch [Recovery Partition].