Chapter 7 Output and Screen Display — Screen status display
- 159 -
6
Remaining recording capacity and status of the memory card
Displays the remaining recording capacity and status of the memory card in card slot 1 or card slot 2.
≥ [0min] to [999min]: Remaining recording capacity (999 minutes or more is displayed as [999min])
j The display will flash when the remaining recording capacity becomes 2 minutes or less.
j The recording capacity available for simultaneous recording (recording capacity for the memory card of the 2 memory cards with less recording
capacity) is displayed when simultaneous recording is performed.
≥ [WP]: Write protected (the write protection switch of the memory card is set to the LOCK side)
≥ [END]: No remaining recording capacity (no remaining recording capacity on the memory card)
≥ [ERR]: A memory card that cannot record is inserted (the card is recognized but cannot record due to a format error, a card other than a memory
card being inserted, etc.)
≥ [!SDXC]: An SDXC memory card is not inserted in MOV recording/MP4 recording
≥ (No display): It is in one of the following conditions.
j A memory card has not been inserted.
j The memory card cannot be recognized.
7
External equipment recording operation control status (<SDI OUT>/<HDMI> terminal)
Displays the control status of the recording start and recording stop on the external equipment connected to the <SDI OUT> terminal and the
<HDMI> terminal.
≥ [SDI]
*1
: Recording instruction is output to the output from the <SDI OUT> terminal.
≥ [SDI]
*1
: Pause instruction is output to the output from the <SDI OUT> terminal.
≥ [HDMI]:Recording instruction is output to the output from the <HDMI> terminal.
≥ [HDMI]: Pause instruction is output to the output from the <HDMI> terminal.
8
Special recording function
Displays the status of special recording function.
≥ [INTRVL]: The interval recording is stopped.
≥ [I-REC]: The interval recording is in progress. (Displayed in red)
9
2-slot function
Displays the setting status of the recording function using 2 memory cards.
It is displayed with a slanted line if it is in a condition that cannot perform 2-slot recording even if each function is enabled.
≥ [RELAY]: When the relay recording is enabled
≥ [SIMUL]: When the simultaneous recording is enabled
≥ [BACKGR]: When the background recording is enabled
≥ (No display): During standard recording
10
Flash band compensation function
≥ [FBC]: Displayed when the flash band compensation function is operating.
11
Streaming status
Displays the streaming status.
≥ : When the unit is connected to a device to receive the streaming video, and the streaming video is distributed
≥ (flashing): When the unit is being connected to a device to receive the streaming video
≥ : When the streaming function is enabled, it is in condition to operate properly, and the streaming video is not distributed
≥ : When there is an error in the streaming function and cannot operate
≥ (No display): When the streaming function is disabled
12
Dynamic range stretcher function
≥ [DRS]: Displays when the dynamic range stretcher function is working.
13
Connection status of the wireless LAN
Displays the connection status of the wireless LAN.
≥ : When set to the wireless LAN and the ROP is not connected
≥ : When set to the wireless LAN and the ROP is connected
≥ : When set to the wireless LAN and the wireless LAN is not operating properly
≥ (No display): When the wireless LAN is disabled
14
Power status
: Displays the remaining battery level while powered with the battery. (The battery status display will change as
while the remaining battery level gets lower. It will flash in red when the remaining battery level is zero.)
: Displayed when powered with the AC adaptor.
15
Audio level meter
Displays the audio level meter.
A white border is displayed in the position of the recording base level (12 dB).
≥ : Displayed when audio cannot be recorded. (When super slow is enabled, etc.)
16
Luminance of Y GET
Displays the luminance level in 0% through 109% when the Y GET function is operating.
17
Gain
Displays the gain value.
≥ [AGC]: Displayed when the auto gain control is operating.
≥ [SG]: Displayed when [SUPER GAIN] is working.
≥ [SGi]: Displayed when [SUPER GAINi] is working.
To Next Page
Loading...
