Panasonic MINAS-BL GV Series - Introduction; Product Designation

－
E7
－－
E6
－
English
Introduction Product designation
Product Overview
This motor is brushless type. Carefully read through this manual so that you will properly
and safely operate it for a long term.
This motor is designed to be built into general-purpose industrial equipment. However, only
properly trained and responsible individuals should operate this product.
<Caution>
When exporting a product containing this motor, make sure that the product will meet the
legal requirements of the destination country.
After unpacking
• Make sure that the model is what you have ordered.
• Check whether the product has been damaged or not during transportation.
If any deciency should be found,
contact the dealer store where you bought this product.
Checking the model of Motor, Amplier and Gear head
This amplier is designed for use in combination with a motor to be specied by us.
Check a name of series, rated output, voltage specications you wish to use
You must not use any other combinations than those listed below:
Failure to observe this instruction could result in breakdowns.
• GV series (Velocity control type)
Shaft
type
Voltage
(V)
Motor size
(mm)
Out put
(W)
Motor Type
Applicable
Amplier
Applicable
Gear head *
Reduction
ratio
Pinion shaft
Single phase
AC100 to 120
□
80 50 MBMU5AZAX MBEG5A1BCV MX8G
○
B 3 to 180
□
90
90 MBMU9A1AZ MBEG9A1BCV
MZ9G
○
B
MY9G
○
B
3 to 200
130 MBMU1E1AZ MBEG1E1BCV
Single phase/
3-phase
AC200 to 240
□
80 50 MBMU5AZAX MBEG5A5BCV MX8G
○
B 3 to 180
□
90
90 MBMU9A2AZ MBEG9A5BCV
MZ9G
○
B
MY9G
○
B
3 to 200
130 MBMU1E2AZ MBEG1E5BCV
Round shaft
Single phase
AC100 to 120
□
80 50 MBMU5AZAS MBEG5A1BCV
－ －
□
90
90 MBMU9A1AS MBEG9A1BCV
130 MBMU1E1AS MBEG1E1BCV
Single phase/
3-phase
AC200 to 240
□
80 50 MBMU5AZAS MBEG5A5BCV
□
90
90 MBMU9A2AS MBEG9A5BCV
130 MBMU1E2AS MBEG1E5BCV
* A gure representing reduction ration in
○
e.g.) Part number of MX type gear head with reduction ratio 10 is MX8G10B.
• Brushless amplier having the sufx V in the model designation is the GV series.
• GP series (Position control type)
Shaft
type
Voltage
(V)
Motor size
(mm)
Out put
(W)
Motor Type
Applicable
Amplier
Applicable
Gear head *
Reduction
ratio
Pinion shaft
Single phase
AC100 to 120
□
80 50 MBMU5AZAB MBEG5A1BCP MB8G
○
BV
5 to 50
□
90
90 MBMU9A1AB MBEG9A1BCP MB9G
○
BV
130 MBMU1E1AB MBEG1E1BCP MB9G
○
BV
Single phase/
3-phase
AC200 to 240
□
80 50 MBMU5AZAB MBEG5A5BCP MB8G
○
BV
□
90
90 MBMU9A2AB MBEG9A5BCP MB9G
○
BV
130 MBMU1E2AB MBEG1E5BCP MB9G
○
BV
* A gure representing reduction ration in
○
e.g.) Part number of MB type gear head with reduction ratio 10 is MB8G10BV.
• Brushless amplier having the sufx P in the model designation is the GP series.