Panasonic PT-60LCX64-K - Page 10

Note:
To release from any service mode, press the POWER
button off.
IC6003 Port Information
P00
P01
P02
P03
P04
P05
P06
P07
Port No.:
P60
P61
P62
P63
P64
P65
P66
P67
Port No.:
P20
P27
Port No.:
P80
P87
Port No.:
P6:11100110
P3:00000000
P0:11100110 P4:11100110
P1:00001110 P5:00001110
P2:11100110 P7:00001110
P8:11100110
Note:
1. The above IC6003 Port information indication means:
1: Hi, 0: Low, -: Port not used
Refer to "I/O CHART OF IC6003."
2. There is a possibility that the IC6003 Port information indication (0 or 1)
of some pins may not correspond to the actual signal condition.
(Sampling cycle: approx. 500 msec.)
IC6302 Port Information
P00
P01
P02
P03
P04
P05
P06
P07
Port No.:
P50
P51
P52
P53
P54
P55
P56
P57
Port No.:
P40
P47
Port No.:
PA0
PA7
Port No.:
P0:001-1111 P5:-----001
P1:-0-0-0-1 P6:11011001
P2:---00111 P7:11101111
P3:00000111 P8:----0101
P4:11110011 PA:----1111
Note:
1. The above IC6302 Port information indication means:
1: Hi, 0: Low, -: Port not used
Refer to "I/O CHART OF IC6302."
2. There is a possibility that the IC6302 Port information indication (0 or 1)
of some pins may not correspond to the actual signal condition.
(Sampling cycle: approx. 500 msec.)
*8: Communication check for IIC bus on the Main C.B.A.
Fig. 1-4-3
*9: EEPROM IC6006 version and build version
*10: EEPROM IC6306 version and build version
*11: IC6003 software version and build version
*12: IC6302 software version and build version
2. Press the CH DOWN key. Service Mode (3/3) will appear.
Fig. 1-5-1
*13 IC6003 Port information
Fig. 1-5-2
<Service Mode (3/3)>
*12
*13
SERVICE Mode P6:11100110 3/3
IC6003 PORT P3:00000000
P0:11100110 P4:11100110
P1:00001110 P5:00001110
P2:11100110 P7:00001110
IC6302 PORT P8:11100110
P0:001-1111 P5:-----001
P1:-0-0-0-1 P6:11011001
P2:---00111 P7:11101111
P3:00000111 P8:----0101
P4:11110011 PA:----1111
0
1
NG
OK
Explanation
Code No.
Communication check for serial bus
(IC6003 IC5302(SCALER))
(Communication check for serial bus)
0
1
NG
OK
Communication check for serial bus
(IC6003 IC5306(FPGA))
0
1
NG
OK
Communication check for serial bus
(IC6003 IC9004
(SD/PC CARD SIGNAL PROCESS) )
IC6003 IC5302 IC6003 IC5306 IC6003 IC9004
IC5302:1 5306:1 9002:1
Note:
The 9002 indicated on the screen is a mistake. It should be "9004."
*14 IC6302 Port information
Fig. 1-5-3
PT-60LCX64-K
10