Panasonic Quasar Omnivision PVQ-1311

27
Timer Operation
VCR Plus+ System Programming
1
2
3
6
7
4
5
SET :
SE L E C T :
END : PROG
SET PROGRAM
T I MER PR OGRAMMING
ON TIMER
VCR P l u s + PR
VCR P l u s + PR
OGRAMMING
OGRAMMING
SE
SE
L E C T C ATE GOR
GOR
Y
28
28
TUE
TUE
12
12
: 00
00
P 12
12
: 30
30
P 69
69
DATE S TART S TOP CH
PBS
SP
SELE
C T :
SET :
END
: P R O G / AC T I ON
- - - - - - - - -- - - - - - - -- - - - - - -
C ATE GOR Y : N / A
C AN C EL : A DD / DLT
SELECT 1 - 8 :
E NTER :
END : P R O G / AC T I ON
P DT STA R T ST O P CH SPD
1
day 9 : 00
00
p 12
12
: 00
00
a 08
08
SP
SP
2 -- -- : -- -- : -- -- --
3 -- -- : -- -- : -- -- --
4 -- -- : -- -- : -- -- --
Selections:
• Categories ➔ N/A (not applicable), SPORTS,
MOVIE, COMEDY, MUSIC, or DRAMA
• Speed ➔ SP, LP, or SLP
To Make Corrections
Press
to move the cursor and to make the
correction.
ENTER PLUS CODE NUMBER
END : PROG
US I NG 0 - 9 KEYS
VCR Plus+ SYSTEM
ONCE
DA I LY (MON
- FR I )
W EEKLY
END : PROG
VCR Plus+ SYSTEM
SET :
SE L E C T :
Ready Check List
The clock is set to correct time.
VCR Plus+ System Setup is
complete. (See page 26.)
Use normal Timer Recording steps if:
• a program PlusCode programming number
is not listed.
• program, such as a sporting event, may run
over scheduled stop time.
See page 25 to:
• cancel a timer recording in progress.
• replace program contents.
• review or clear program contents once set.
• You can obtain unlisted PlusCode
programming numbers by calling
1-900-454-7587.
Call costs approximately $.95 per minute.
• Avoid overlapping program times.
• If you’re using a cable box, make sure that
it is tuned to the desired channel and the
power is left on for timer recording.
• Timer programs memory capacity is 8.
To add more programs, please first clear
other programs. (See page 25.)
• Make each entry within 5 minutes or the
unit will leave this mode.
• Once local channels have been
programmed, they will stay in memory,
even in the case of a power failure.
Notes
Notes
Press PROG/VCR+
to display SET PROGRAM screen.
1) Press to select
VCR Plus+
PROGRAMMING
.
2) Press
to display
screen.
1) Press number keys
to enter PlusCode
programming number.
2) Press PROG/VCR+
when finished.
1) Press to select
and to set
Record Frequency.
1) Press to select
and to set
Category and
Record speed.
Press PROG/VCR+
(or ACTION.)
to end programming.
Press PROG/VCR+ twice (or ACTION)
to exit this mode.
• PROG TIMER indicator lights on the unit.
To Make Corrections
Press repeatedly to delete
the PlusCode programming number.
VCR Plus+ and PlusCode are
registered trademarks of Gemstar
Development Corporation.
The VCR Plus+ system is
manufactured under license from
Gemstar Development Corporation.
*
Important: if a remote control button does not work when pressed, press the COMBO button on
the remote and try the button again.
C2061- P26-27 VCR+ 00.12.14, 5:33 PM27