Panasonic RAMSA WR-S208 - Output Specifications

(5) Meter Selector SWitcnes
These switch es are used for se lect ing signals to be
displayed by {he 12 - po i nt LED bar-graph meters lA /Ef-
fect and B/ Send) .
Meter
S wit ch
Indication
A / Effect A Sub A output
Effect
Effect output
B/Send
B
Sub B out put
Send
Send
output
(6) Effect Return Controls
These controls are used for adjust i ng the level of i n-
put signals returning from the various effects
dev ices.
(7) Pan
Controls
These controls are used to divide the incoming ef-
fect return signal between the stereo Sub A and Sub
B outputs
Input
Pan pot position
Output
Eff e ct Center
Sub A and Sub 8
Return
1 I Counterclock
Sub A
wise
Clockwise Sub B
Effect
Center
Sub
A and Sub B
Re t urn 2
Counterclock -
Sub
A
wise
Clockwi se Sub 8
(8) Sum Peak Indicator LEOs
These
LEOs light at + 14 dB, wh i ch;s 6 dB down from
the summing point (pre- fader l evell clipping level ( + 20
dB). If this LED light s, output signals will be distorted .
Lower each input fader so that the LED w ill not light.
(9) Sub A and Sub B Output Faders
60 mm carbon faders for adjusting the master outp ut
levels of Sub A and Sub B.
Position 0 represents the rated ou t put level.
(10) Monitor Output Fader
A
60 mm carbon fader for adjusting master monitor
output level.
Posi tion 0 represents the rated output level.
(11) Send Output Fader
A
60 mm carbon fader fo r adju sting master Send out-
put level.
Position 0 represents the rated outpu t level.
(12) Effect Output Control
Th is control is used for adjusting the master Effect
output level.
Position 10 (fully clockwise) represents th'e rated out -
put level.
- 10 -
(13) Record Output Level
This control is used for adjusting re cord outpu t level.
Channel A and Channel B are simu ltaneously adj usted .
Sub A and Sub 8 pre-fader leve l signals feed this
control.
(14) Main Output Pre/Post Selector Switch
This switch is used for switching Main output si gnals
to Sub A and Sub B pre- fader si gnals or po s t-fader
signals .
Depressi ng the switch to the down position selects
pre-fader level , and pressing it again to the up posi-
tion selects post - fader level .
Pre: Signals before the Sub A and
Sub B fader are sent to the Ma in
output .
Post :
Note :
Si gnals after the Sub A and Sub B
faders are sent to the Ma in
output _
In "POS{ " position Sub A and Sub B faders must be
raised for signal to be present at Main output .
(15) Main Output Fader
A
60 mm carbon fader for Main output level
adJ ustment .
Posit i on 0 represen ts the rated output level.
Ma in output signa l is (J monaural signal summed from
Sub A and Sub B signals .
(16) Control Room Monitor Selector Switch
This switch is used for selecting control room mo ni tor
ou t put and headphone signals.
Si gnals that can be selected are: Sub A /B ou t put, Main
output, monitor output, Send output, and Effect
output.
If the channel solo switch is pressed, solo signals are
sel ected regardless of switch position .
(17) Control Room Monitor/Phones Control
This control is used for cont rol r oom mon it or output
level adjustment .
Headp h one monito r level is also adjusted.
(18) Solo Control
This control adjusts the level of the solo signal present
at the control room and headphone outputs .
(19) Solo Indicator LED
This LED ligh ts if anyone of the input chan nel solo
switches is on.
(20) Phones
1/4 " TRS phone jack for headphones.
MaXimum output is 1.2 W + 1.2 W 18 ohms .