Panasonic RAMSA WR-S216 - Features; Overall; Mono Input Section; Stereo Input Section

FEATURES
Overall
1, Each of the three types of stereo mixers have two
stereo input channels, which accept phono inputs
and tape/aux inputs, and are designed to be more
compact than ever before despite the number of
Inputs provided,
WR-S208
WR-S212
WR-S216
Mic
x8
x12
x16
Phono
x2
x2
x2
Tape/Aux
x2
x2
x2
The WR-S208 has the same number of inputs as
a 12-input mixer.
The WR-S212 has the same number of inputs as
a
16-input mixer.
The WR -$ 216 has the same num be r of Inputs as
a 20-input mixer.
2. Separate microphone and line inputs are provided,
eliminating the need for repatchlng, Both
microphone and line inputs are electronically
balanced.
3 , The three send circuits can be used for effects and
monitoring, further widening the range of
a ppl icatlons.
Monitor output:
E Hect output:
Send output:
Pre-fader level
Post-fade r level
Pre-/post-fader level
(switchable)
4 _ Stereo output circuits (Sub A and Bl and one mono
output (Main) circuit are provided , The main out IS
the combination of Sub A and Sub B output signals.
This signal can be derived pre- or post- sub output
fader,
r- --~!$J S ub B
A Pre Fader
A
Post
L = ~~,e~~>-'W'--.J-!> - ~ "- - - - 0' Main
BPost XJ-------v- ~
mr'
5. A phantom power supply of + 48 V is provided for
condenser microphones.
6. Aluminum diecast end panels insure mechanical
stability.
7. The WR-S208 can be mounted in a rack, using op-
tional rack fittings.
- 1 -
8, The semi-modular input structure combining four
channels together eases repair and testing.
Mono Input Section
1. Exclusive microphone Input connectors and line In-
put jacks are provided,
Microphone/line input selection is accomplished
With mechanically-interlocked pushbutton
switches .
2. Three-band equalizers are provided. Turnover fre-
quencies are 10kHz, 400 Hz - 6 .3 kHz
(sweepable), and 100 Hz for High, Mid, and Low
respectivr.ly.
High: Shelving type ± 1 5 dB
Mid: Peaking type ± 1 5 dB
Low Shelving type ± 1 5 dB
3. A peak Indicator LED is provided for each Input for
monitoring input signal level,
4. Each Input is prOVided with a solo switch for in-
dividual monitoring .
5. An insertion circuit is provided for connecting ef-
fects devices to individual input channels,
6. Three send circuits are provided .
Monitor: Pre-fader level
Effect : Post-fader level
Send :
Stereo Input Section
Pre-fader level/post fader
level (selectable)
1. A microphone input connector, phono input jacks,
and tape/aux input Jacks are provided so that patch
work is no longer necessary.
2, Phono and tape/aux input levels can be In-
dependently controlled.
3, The microphone input has a separate on/off switch.
4 . A Mono/Stereo selector s~itch is included on
Stereo input channels,
5. Two-band stereo equalizers are provided with turn-
over frequencies of 10kHz (High) and 100 Hz
(Low),
High :
Low :
Shelving type ± 15 dB
Shelving type ± 15 dB
6, Two send Circuits are provided,
Monitor: Pre-fade r level
Effect: Post-fader level
7. A monaural solo switch is provided for input
man itoring.
8. Peak indicator LEOs are prOVided for monitoring in-
put signal level.