Panasonic S-36PF1U6 - Page 169

1-1611-160
1. Specifications
<Procedure of CZ-RTC3 /CZ-RTC5>
Stop the system before performing these steps.
1
Keep pressing the
, and buttons
simultaneously for 4 or more seconds.
The “Maintenance func” screen appears on the LCD display.
2
Press the or button to see each menu.
If you wish to see the next screen instantly, press the
or button.
Select “8. Detailed settings” on the LCD display and press
the
button.
The “Detailed settings” screen appears on the LCD display.
3
Select the “Unit no.” by pressing the or button
for changes.
4
Select the “Code no.” by pressing the or button.
Change the “Code no.” to “
” by pressing the or
button (or keeping it pressed).
=91
=90
=92
=93
Electrical component box
5
Select the “Set data” by pressing the or button.
Select one of the Setting Data “YYYY” by pressing the
or button.
Then press the button.
Flap position
1
2
3
4
5
Fig. 1-142
* Setting data “
” (refer to Fig. 1-142)
Setting dataFlap position during operation
Without separate setting
Swing
Move to position
1
and stay
Move to position
2
and stay
Move to position
3
and stay
Move to position
4
and stay
Move to position
5
and stay
When the flap position is set to
4
or
5
and the unit is
in the cooling or dry mode, the flap position is moved to
3
and the operation is started. (refer to Fig. 1-142)
NOTE
The flap swings during the operation under “Setting the
Flap Separately”.
At this time, the unselected flaps are moved to the
position
1
. (refer to Fig. 1-142)
6
Press the button.
The “Exit detailed settings and restart?” (Detailed setting-
end) screen appears on the LCD display.
Select “YES” and press the
button.
00_271724_Eng.indb 25 2015-8-26 14:44:14
If you wish to change the selected indoor unit, follow the
step
2
.
<Procedure of CZ-RTC4>
Stop the system before performing these steps.
1
Press and hold the
, and buttons
simultaneously for 4 seconds or longer.
2
If group control is in effect, press the
button to set. At
this time, the fan at the indoor unit begins and select the
address (unit No.) of the indoor unit operating.
3
Designate the item code “
” by adjusting the Temperature
Setting
/ buttons.
=91
=90
=92
=93
Electrical component box
4
Press the timer time
/ buttons to select the desired
setting data.
Flap position
1
2
3
4
5
Fig. 1-143
* Setting data “
” (refer to Fig. 1-143)
Setting dataFlap position during operation
Without separate setting
Swing
Move to position
1
and stay
Move to position
2
and stay
Move to position
3
and stay
Move to position
4
and stay
Move to position
5
and stay
A
°
°
When the flap position is set to
4
or
5
and the unit is
in the cooling or dry mode, the flap position is moved to
3
and the operation is started. (refer to Fig. 1-143)
NOTE
The flap swings during the operation under “Setting the
Flap Separately”.
At this time, the unselected flaps are moved to the
position
1
. (refer to Fig. 1-143)
5
Press the
button.
(The display stops blinking and remains lit, and setting is
completed.)
If you wish to change the selected indoor unit, follow the
step
2
.
6
Press the
button to return to normal remote controller
display.
00_271724_Eng.indb 26 2015-8-26 14:44:16
1
SM830203-04.indb 161 15/10/16 10:45:12