Panasonic S-36PF1U6 - Page 190

1-1831-182
1. Specifications
CZ-RWSU3U
7-12. Supplied Accessories
7-13. Installing the Receiver
The receiver can only be installed on the corner indicated in Fig. 1-219. Consider how the panel will
face when it is installed on the indoor unit.
1 Remove the air inlet grill.
2 Remove the screw holding the adjustable corner cover. Then slide the cover to the side and remove it. (Fig. 1-220)
3 To pass the wire through the panel, bend the part (shaded area) on the square hole and then
pass wire protrudingfrom the wireless receiver through the grill. (Fig. 1-221)
4 After wiring according to the directions in “Wiringfor the Receiver”, leave enough wire length so that the
receiver’s adjustable corner cover can be removed andfasten the wire with the clamper. (Fig. 1-221)
5 Hang the corner cover string on the pin of the ceiling panel (Fig. 1-222). Then slide the corner cover
onto the ceiling panel until the three clips are correctly located, and then fix it in place with the screws.
Fig. 1-219
Fig. 1-220
Fig. 1-221 Fig. 1-222
Make sure the wire is not caught.
Refer to the installation instructions supplied with the panel.
For more information about wiring and test operation, see the sections on “Wiring for the Receiver” and
“Test Operation”
TD831159-042WAYVRF.indb19 2014/08/2613:48:00
Wireless Remote
Controller
(1)
Remote Control
Holder
(1)
AAA Size
Battery
(2)
Operating
Instructions
(1)
Wood Screw
(2)
Clamper
(1)
Supplied Accessories
Box with
indoor unit’s
electrical
parts
Receiver position
Screw
Adjustable corner cover
Ceiling panel
Adjustable corner cover
Pin.
Fix the
screw.
Bend the part (shaded
area) with a screwdriver
or similar implement to
allow the wire to pass
through.
Fix it in place
with the
clamper.
Make sure the three clips on the corner
cover are located over the holes on the
ceiling panel and fix it in place with the
supplied screws.
7-14. Wiring for the Receiver
Wiring Diagram
How to Connect the Wires
Connect the wires from the receiver to the terminals for RC wiring on the indoor unit. (No polarity)
7-15. Test Operation
Attention
Preparation : Turn on the circuit breaker of units and then
turn the power on. After the power is turned
on, remote controller operation is ignored for
approx. 1 minute because setting is being
made. This is not malfunction. (Contents
received while setting are disabled.)
1. To start test operation, press and hold the emergency
operation button for 10 seconds.
2. The indication lamps (OPERATION, TIMER, STANDBY)
blink during test operation.
3. To finish test operation, press and hold the emergency
operation button for 10 seconds.
7-16. Setting Address Switches
CZ-RWSU3U
TD831159-042WAYVRF.indb20 2014/08/2613:48:00
Indoor unit
CN001
1
2
2P White
Receiver PCB
Terminals for RC
wiring
Do not use this mode for purposes other thanthe test
operation. (To prevent overload of the units)
Read the installation instructions supplied with the units.
Any of the Heat, Cool and Fan operations can only be
performed.
Temperature cannot be changed.
The test operation mode is automatically turned off in
60 minutes. (To prevent continuous test operation)
Outdoor units do not operate for approx. 3 minutes after
the power is turned on or operation is stopped.
Before installing the receiver, see the sections on
“Wiringfor the Receiver” and “Setting Address Switches”.
Then check the settings of the [S003] DIP switch on the
receiver’s PCB.
*Remove the cover from the receiver when performing the
PCB settings.
ON
Main/Sub selector
switchfor remote
controllers (4)
OFF : Main
ON : Sub
Screw
Clamper
PCB
cover
Receiver
PCB
Corner
cover
Set its address
(1) to (3)
All set at OFF
when shipped
from the factory.
When more than 1 receiver is installed in the same room, setting addresses prevents
interference.
For how to change addresses of wireless remote controllers, see the operating instructions of
wireless remote controllers.
To change the receiver’s address, remove the cover from the receiver’s PCB and set No.1 to
No.3 of the [003] DIP switch on PCB.
Remote
Controller
Address
Display
Address Address Address Address Address Address Address
ON/OFF
States
ALL 1 2 3 4 5 6
Position
of the
receiver’s
address
switch
Receipt is
possible
at all
of the
address
positions
1234 1234
1234
1234
1234
1234
OFFON
1
SM830203-04.indb 182 15/10/16 10:45:22