VQC9513
Yes No / Do not know
NoYes
Start wireless network settings
Preparation
1 Place SC-PMX9 close to the wireless network router as
possible and then point the antenna on the rear of the main
unit up as shown in the figure.
≥ Do not tilting the antenna forward or backwards when it is pointing up.
2 Connect the AC mains lead while the LAN cable is disconnected.
3 Turn this system on.
4 Follow the chart below to choose the network setting method.
≥ If you want to perform wireless setting with your Mac/PC, or you want to apply the advanced
setting, refer to
“Method 4” in the operating instructions.
You can make the wireless network
settings with the app, “Panasonic
Stereo System Network Setup” (for
free).
If you’re using an Android device,
download the app at Google Play
TM
. If
you’re using an iPod touch/iPhone/
iPad, download it at the App Store.
Preparation
≥ Connect your smartphone to your
home wireless network.
≥ Check the password for your home
wireless network.
∫ Note for the iOS version
After step 3
1 Enter the password for the home
wireless network to which the iOS
device is connected.
2 When a message instructing you
to connect the iOS device to this
system is displayed, press the
home button.
3 On the Wi-Fi network selection
screen in “Settings”, select
“00 Setup _ _ _ _ _ _”.
4 When a message indicating the
completion of the connection to
this system is displayed, restart
the app.
5 When a message indicating the
completion of the Wi-Fi setup of
this system is displayed, close the
app, and then check the operation
of AirPlay, etc.
1
Press [SETUP] on the remote
control repeatedly to select
“Net Setup” and then press [OK].
“With iPod” is indicated on the display.
2
Press [SETUP] on the remote
control repeatedly to select
“Manual” and then press [OK].
3
Start “Panasonic Stereo System
Network Setup” on your
smartphone and follow the
indications.
Using AirPlay
The following explanations are based on an iPhone.
≥ AirPlay, the AirPlay logo, iPad, iPhone, and iPod touch are
trademarks of Apple Inc., registered in the U.S. and other countries.
≥ App Store is a service mark of Apple Inc.
≥ Android and Google Play are trademarks of Google Inc.
≥ The Wi-Fi CERTIFIED Logo is a certification mark of the Wi-Fi
Alliance.
≥ The Wi-Fi Protected Setup Mark is a mark of the Wi-Fi Alliance.
≥ “Wi-Fi” and “Wi-Fi Protected Setup” are marks or registered marks
of the Wi-Fi Alliance.
≥ All other trademarks are trademarks of their respective owners.
1 Connect the iPhone to your home wireless network.
2 Select “Panasonic PMX9 _ _ _ _ _ _” from the AirPlay icon and start play.
Does your wireless network router support
WPS (Wi-Fi Protected Setup
TM
)?
Are you using an iPod touch/iPhone/iPad?
Is the iOS version 5.0 or later?
Method 1 Method 2 Method 3
1
Press [SETUP] on the remote
control repeatedly to select
“Net Setup” and then press [OK].
“With iPod” is indicated on the display.
2
Press [SETUP] on the remote
control repeatedly to select “WPS
Push” and then press [OK].
“WPS” flashes on the display.
3
Press the WPS button on the
wireless network router.
4
Press [OK] on the remote control
to exit.
4
Press [SETUP] on the remote
control repeatedly to select
“Net Setup” and then press [OK].
“With iPod” is indicated on the display.
5
Unlock your iPhone and then
press [OK] on the remote control.
6
A message will pop-up on the
iPhone. Allow the iPhone to share
the wireless network settings.
7
The settings are completed when
“Success” is displayed and “ ”
is indicated on the display.
8
Press [OK] on the remote control
to exit.
To Next Page
Need help?
General
