Panasonic SC-PT70

10
RQTX1019
Getting StartedPlaying DiscsOther OperationsReference
Setting up the radio
Up to 30 stations can be set.
≥“SET OK” is displayed when the stations are set, and
the radio tunes to the last preset station.
≥“ERROR” is displayed when automatic presetting is
unsuccessful. Preset the channels manually (B right).
≥The FM setting is also shown on the TV display.
To cancel the mode, press and hold the button again until
“AUTO ST” is displayed.
≥The mode is also cancelled when you change the
frequency.
Up to 30 stations can be set.
A station previously stored is overwritten when another
station is stored in the same channel preset.
Selecting the playback source
You can select sound effects, desired source, or access
playback/menus by using the START menu.
When “Input Selection” is selected
You can select a desired source from the menu.
≥DVD/CD (B 9), FM (B 10), AV (B right),
AUX/TV (B right), MUSIC PORT (B 17)
When “Sound” is selected
You can select sound quality settings (B 11, Equalizer).
When a disc is loaded, you can also access playback or
menus from the START menu.
e.g. [DVD-V]
When the on-screen control panel appears
e.g. [DVD-V] (when “Playback Disc” is selected from the
START menu)
You can operate the playback with the indicated controls.
[Note]
Confirm the audio connection to the SCART (AV) or
AUX/TV terminal on this unit when you select the
corresponding sources (B 8). Reduce the volume on the
TV to its minimum, and then adjust the volume of this
unit.
Presetting stations automatically
1
Press [RADIO]@ to select “FM”.
2
Press [MENU]:.
Each time you press the button:
LOWEST (factory preset):
To begin auto preset with the lowest frequency.
CURRENT:
To begin auto preset with the current frequency.
§
§
To change the frequency, refer to “Manual tuning”
(B right).
3
Press and hold [OK]9.
Release the button when “FM AUTO” is displayed.
The tuner starts to preset all the stations it can
receive into the channels in ascending order.
Confirming the preset channels
1
Press [RADIO]@ to select “FM”.
2
Press the numbered buttons to select a channel.
≥To select a 2-digit number
e.g. 12: [S10]3 B [1] B [2]
Alternatively, press [X, W]6.
If noise is excessive
Press and hold [PLAY MODE]2 to display “MONO”.
Manual tuning
1
Press [RADIO]@ to select “FM”.
2
Press [6, 5]A to select the frequency.
≥To start automatic tuning, press and hold [6,
5]A until the frequency starts scrolling. Tuning
stops when a station is found.
Presetting stations manually
1 While listening to the radio broadcast
Press [OK]9.
2 While the frequency is flashing on the display
Press the numbered buttons to select a channel.
≥To select a 2-digit number
e.g. 12: [S10]3 B [1] B [2]
Alternatively, press [X, W]6, and then press [OK]9.
Selecting the source from the START menu
1
Press [START]C to show the START menu.
This unit automatically turns on.
(The TV also turns on when using VIERA Link “HDAVI
Control”. This works only when in “DVD/CD” mode
without any disc being loaded.)
e.g.
2
Press [ 3 , 4 ] 9 to select an item and press [OK] 9 .
≥To exit, press [START]C.
3
Press [ 3 , 4 ] 9 to make the setting and press
[OK]
9 .
DVD/CD Home Cinema
OK
Input Selection
Sound
DVD/CD Home Cinema
Input Selection
Sound
Playback Disc
TOP MENU (DVD)
MENU (DVD)
Playback/menu access
Selecting the source by the remote control
Press To select
[DVD]@ DVD/CD
[RADIO]@ FM
[EXT-IN]@ Each time you press the button:
AV: For audio input through the
SCART (AV) terminal.
AUX/TV: For audio input through the
AUX/TV terminal.
MUSIC P.: For audio input through MUSIC
PORT. (B 17)
SC-PT70EB-RQTX1019-B_eng.book Page 10 Thursday, August 13, 2009 5:07 PM