Panasonic TC-42PX14

(Continued)
==Menu list
Time (minutes)
4:3 side bars
Scrolling bar
VIERA Link
Sets the mode to select the channel with Channel up/down button
(All/Favorite/Digital only/Analog only)
e Favorite: Only_channels registered as FAVORITE
Selects the screen menu language
Adjusts the clock
Sets channels
Selects the terminal and label of the external equipment
Power on link
Power off link
Stand-by power Set "Stand-by power save"of HDMI connectionequipment. (No/Yes)
save
Auto power Set "Auto power stand-by" of HDMI connection equipment.
stand-by (No/Yes (with reminder)/Yes (no reminder)
Default Selects the default speakers (W/Theater)
speakers
No signal for 10
minutes
No activity for 3
hours
Auto power on
Play SD card
automatically
About
Reset to defaults
nSub menu list
Prevents "Image retention" with Wobbling. (Automatic/Periodic)
® Automatic: Shiftsthe displayimage automatically.
• Periodic: Shiftsthe displayimage every (1/21314)minutesaccordingto whatwas set in the
"Time (minutes)"menu.
Sets the time for "Pixel orbiter-Periodic"setting. (1/2/3/4)
Change the brightnessofthe side bar (Off/Dark/Mid/Bright) (4:3 mode only)
® The recommended settingis "Bright" to preventpanel "lmaqe retention".
Press "OK" to start horizontal"Scrolling" on the screen
Controls equipmentconnectedto HDMI terminals (On/Off)
o "Power off link","Power on link","Stand-by power save" and, "Auto power stand-by",
"Default speakers"cannot be selected if "Off" is set.
Sets "Power on link"ofHDMI connectionequipment(Yes/No)
Sets "Power off link"of HDMI connectionequipment (Yes/No)
To conserve energy, the TV automatically turns off when NO SIGNAL and NO OPERATION is
_erformed for more than 10 minutes. (Enable/Disable)
Note
Not in use when setting "Auto power on", "On/Off Timer", "Lock", "SD mode" or Digital
channel.
• "No signal for 10 minutes was activated" will be displayed for about 10 seconds when the
TV is turned on for the first time after turning the power off by "No signal for 10 minutes".
• The on-screen display will flash 3, 2 and 1 to indicate the last three (3) remaining minutes prior to
the shut-off.
To conserve energy, the "IV automatically turns off when no operation of remote or side panel
key continues for more than 3 hours. (Enable/Disable)
Note
Not in use when setting "Auto power on", "On/Off Timer" or PC input display.
"No activity for 3 hours was activated" will be displayed for about 10 seconds when the TV is
turned on for the first time after turning the power off by "No activity for 3 hours".
The on-screen display will flash 3, 2 and 1to indicate the last three (3) remaining minutes prior to
the shut-off.
Turns TV On automatically when the cable box or a connected device is turned On (No/Yes)
TVAC cord must be plugged into this device. TV comes on every time the power is restored.
The "Sleep" timer, "On / Off timer", and "First time setup" will not function if "Auto power on"
is set.
Set "Thumbnail" or "Slideshow" to play back SD cards automatically.
(Slideshow/Th umbnail/Set later/Off)
Displays TV version and software license.
Performing Reset willclear all items set with Setup, such as channel settings.
_ Sets the mode to select the channel with Channel up/down button
Channel surf mode (All/Favorite/Digital only/Analog only)
Set favorite Sets favorite channels.
_ Edit OH caption Changesthe station identifier.
_ Signal meter Checks the signal strength if interference orfreezing occurs on a digital image.
17