Panasonic TX-40MS490B - Advanced Setup and Home Screen; Satellite and Channel Scan Configuration; Home Screen Navigation and Features

English - 12 -
 screen will be displayed
next. First Antenna type(*) should be set. Universal,
Single Cable and Jess Singlecable options are
available. Set the Antenna Type as Universal for
Direct and DiSEqC satellite systems. If you set the
antenna type as Universal, press the Right directional
button to proceed to the next step. If the antenna
type is set as Single Cable or Jess Singlecable,
there will be three more additional options on the
 screen: Tuner, Band
frequency and .  option
will be available if the Band frequency is set as User
. Set these options if available and press the
Right directional button to proceed.
(*) This option may be named as Satellite type depending on
the country selection.
Depending on the country and satellite type selections
you made in the earlier steps of the initial setup
process, Load Preset List screen may be displayed
next. Highlight Load Preset List and press OK or the
Right directional button to proceed with the SatcoDX
installation. You can also skip this step by selecting
Skip option.
After the parameters on the  
Setting screen are configured according to your
environment and preset list installation preference is
selected the next step may be Select Satellite screen.
󰀨
on the selected antenna type and operator in the
previous steps. Highlight the desired satellite option
and press OK to set the parameters(*). The Satellite
StatusOn. In

enable scan this option should be set as On
Back button and select next satellite you want to set.

the Right directional button to proceed.
(*) If you have a Direct satellite system, DiSEqC Set option
should be set as DiSEqC A.
If Load Preset List option is selected in the previous
step next steps will be skipped and the preset channel
list installation will start. If the correct satellite has not
been selected for SatcoDX installation, a warning
dialogue will be displayed on the screen. The satellite/s
that can be selected will be listed. Press OK to close
the dialogue and then set the satellite accordingly.
Channel Scan screen will be displayed next. Select
Scan and press OK or the Right directional button
      
Skip Scan to proceed without performing a scan and
complete the initial setup.
 screen will be displayed next
if Scan option is selected. Following options will be
available: Scan Mode and Channels. You can choose
to perform a full scan or a network scan. Set the
Scan Mode accordingly. If you are going to perform a
network scan, make sure that you have adjusted the
Frequency, Symbol Rate (Ksym/s) and Polarisation
parameters under the Transponder option accurately
on the Satellite Setup screen. You may not be able
to change the Scan mode setting depending on the
previous selections. If the Channels option is set
as Free encrypted channels will not be installed.
Additional options may also be available depending
      
according to your preferences. Once you are done
with setting the available options, press the Right
directional button to start scan while Scan Mode or
Channels is highlighted. While the search continues
you can press the Back button to cancel the search.
The channels that have already been found will be
stored in the channel list.
When the initial setup is completed results will be
displayed. Press OK
Next, you will need to agree to the terms and conditions
of Freeview Play to make use of the related services.
Scroll the page to read the entire text using the up/
down directional buttons. Highlight Accept and press
OK
Skip and press OK
For further requirements for Freeview Play services
refer to the Freeview Play Platform section.
Home Screen will be displayed. You can highlight Live
TV app and press OK to switch to Live TV mode and
watch TV channels.
Home Screen

be connected to the Internet. Connect the TV to a
home network with a high-speed Internet connection.
You can connect your TV wirelessly or wired to your
modem/router. Refer to the Network & Internet
and Connecting to the Internet sections for further
information on how to connect your TV to the internet.
The Home menu is the centre of your TV. Press the
Home button to display Home Screen. From the
Home menu you can start any application, switch to a
TV channel, watch a movie or switch to a connected
device. Depending on your TV setup and your country
selection in the initial setup the Home menu may
󰀨
The available options of the Home Screen are posi
-
tioned in rows. To navigate through the Home Screen
options use the directional buttons on the remote.
Apps, YouTube, Google Play Movies & TV, Google
Play Music and Google Play related rows and rows of
the applications you have installed might be available.
Select a row then move the focus to the desired item
in the row. Press OK button to make a selection or to
enter a sub-menu.
On the upper left of the screen, search tools will be
located. You can choose either to type a word to start