EasyManua.ls Logo

Paradox NV35M

Paradox NV35M
2 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
PARADOX.COM
Installation Manual v1.0
Outdoor/Indoor
Window and Sliding Door
Dual Detector with
Anti-Masking and
Pet Immunity
NV35M-EI01
General Description
Thank you for choosing the NV35M for your professional protection needs.
The NV35M wired version will provide you the most advanced window and
sliding door protection either in Pet Immune or Sharp mode. If you have
any comments please write to us at Paradox.Com/products/feedback.
This guide describes how to install and program the NV35M.
Installing the NV35M
1. Remove the NV35M front cover - open the Captive screw.
2. Remove the Main Unit: open the two snap-lock mechanisms on each
side of the back cover attaching the Main Unit to the back cover as
displayed below. Then remove the Main Unit.
Figure 3 – Removing the Main Unit
3. Pull the wires from the control panel through the knockout holes and
mount the back cover onto the window frame or wall using screws.
Figure 4 – Mounting the Back Cover
4. Attach the Main Unit to the back cover - ensure the locks snap closed.
Figure 5 – Attaching the Main Unit
5. Connect the wires to the terminal blocks according to the following
wiring assignment.
Table 1: Wiring Assignment
6. Set the following Detector settings according to requirements.
Figure 6 – Detector Settings
The following table displays the Dip Switch settings.
Table 2: Dip Switch Settings
7. Replace the front cover and close the Captive screw.
Warning: Do not obscure the detector's field of view.
Figure 1 – Removing the
Front Cover
Figure 2 – Main Unit
Front cover
Captive screw
Knockout
holes
Mounting
screw 1
Mounting
Tamper
screw 2
Tamper
knockout
hole
Terminal Connector Recommended Wiring Assignment
1 12V+
2 Minus (-)
3 Fault indication
4 Tamper indication
5 Common (Fault & Tamper)
6 Alarm indication
7 Common (Alarm)
Dip Switch
Number
Function Mode Description
1 LED
ON: LED on (default)
OFF: LED off
2
PET Immunity/
SHARP Mode
ON: PET Immunity mode (default)
OFF: SHARP mode
1
23
Dip Switch
Sensitivity Trimmer
LED flashes green 1-3 times
according to the selected
level
NV35M
Question and Answer IconNeed help?

Do you have a question about the Paradox NV35M and is the answer not in the manual?

Paradox NV35M Specifications

General IconGeneral
TypeMotion Detector
CompatibilityParadox Security Systems
Tamper SwitchYes
Operating Temperature-10°C to +50°C
Detection MethodInfrared
Detection Angle90 degrees
Power Source12V DC

Summary

NV35 M Installation Guide

General Description

Overview of the NV35M detector for professional protection needs, detailing its use in Pet Immune or Sharp mode.

NV35 M Installation Steps

Step-by-step instructions for physically installing the NV35M detector, including cover removal and wiring.

Wiring and Terminal Assignments

Details the specific wire connections required for the NV35M detector to the terminal blocks.

Detector Settings Configuration

Guidance on setting the NV35M detector's sensitivity and mode using dip switches.

NV35 M Operation and Specifications

Walk-Test Procedure

Instructions for performing a walk-test to verify the successful installation and detection range of the NV35M.

Beam Pattern Visualization

Visual representations of the NV35M's detection coverage in PET and SHARP modes from side and top views.

LED Status Indicators

Explanation of the NV35M's LED indicators and their status messages for various events.

Technical Specifications Summary

Key technical details of the NV35M, including sensor type, detection range, power, dimensions, and certifications.

Warranty and Compliance Information

Details on the product warranty, user compliance, and patent information for the NV35M detector.

Related product manuals