Parker EXACTOL 400 Series - Model 424 Parts Schematic

Bulletin 4391-B400S
EXACTOL
®
400 Series Tube Benders
10
Parker Hannifin Corporation
Tube Fittings Division
Columbus, OH
www.parker.com/tfd
Model 424 Parts Schematic
Model 424 Tube Bender/Maintenance and Parts List
Bender Maintenance
All parts should be kept clean and free from dirt and
grit. Slide block and radius blocks should be handled
carefully to avoid damaging the smooth grooved surfac-
es. Presence of nicks, burrs, pieces of dirt or chips may
mar the surface of the tube and thereby weaken it.
All threaded parts should be cleaned and slightly
greased occasionally to keep them in good working
condition. This equipment will operate efficiently for a
long period of time and will bend to exact tolerances
repeatedly if these precautions are heeded.
Model 424 Parts List (Part # 621044)
Item
# Description
Part
No.
No.
Req’d
1 Body 621062 1
2 Dowel Pin, 5/8 x 1-1/2 13102 1
3 Worm 621067 1
4 Shaft 621068 1
5 Collar 621069 1
6 Snap Ring Truarc #5100-75 56 x 212 1
7 Key, 3/16 sq. x 1-5/8 long 13110 1
8 Pin, Driv-lok Type A 1/4 dia. x 1 13111 1
9 Subassembly Work & Shaft 621066 1
10 Bearing, #D2620 13113 1
11 Bearing, #3038DS 13114 1
12 Bearing, #607 13115 1
13 Pin, Driv-lok Type E 1/4 dia. x 1-1/4 13117 1
14 Nut, Drive 621071 1
15 Plug, Bearing Retainer 621072 1
16 Screw, Pilot Adjusting 621073 1
17 Bearing, Flange, #FF-1102-6 “Oilite” 13123 2
18 Nut, Vise Jaw 621074 1
19 Pin, Vise Jaw Nut 621075 1
20 Screw, Vise Jaw Adjusting 621076 1
21 Vise Jaw 621077 1
22 Pin, Vise Jaw Adjusting Screw 621078 1
23 Center Post Subassembly 621079 1
24 Bearing, #55507 N.D. Double Row
Ball
13136 1
25 Gear, Worm 621080 1
26 Key, Worm Gear 1/4 sq. x 19/32 long
22x20
13160 2
27 Nut, Worm Gear Retaining 621081 1
28 Bearing, #499604 N.D. Single Row
Ball
13141 1
29 Lockwasher, #W-04 13142 1
30 Locknut, #N-04 13143 1
31 Guard, gear 621082 1
32 Screw, 1/4-28 x 5/8 long Round Hd.
Mach. 4 x 126
13367 1
33 Pin, Drive 621083 2
34 Tie, Bar 621084 1
35 Adapter & Pin Subassembly, Slide
Block
621085 1
36 Screw, 5/10-18 x 3/4 Soc. Hd. Cap 13152 1
37 Crank-handle Subassembly 621063 1
38 Nameplate 550609 1
39 Screw, #0 x1/8 Type “U” P.K. 13050 4
41 Center Post 13157 1
42 Drive Plate 13159 1
43 Key, 1/4 sq. x 19/32 13160 1
44 Washer 621070 1
45 Washer 621070 1
46 Dowel Pin 5/8 13163 1
47 Vise Jaw Adapter 13165 1
48 Dowel Pin 1/4 13166 1
67 Crank Handle 13168 1
68 Knob 13054 1
69 Screw 13055 1